PIC24FJ64GB004-I/ML Microchip Technology, PIC24FJ64GB004-I/ML Datasheet - Page 7

• Manufacturer Part Number: PIC24FJ64GB004-I/ML
• Description: IC, 16BIT MCU, PIC24F, 32MHZ, QFN-44
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ64GB004-I/ML

• Controller Family/series: PIC24
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, LIN, SPI, UART, USB
• No. Of Pwm Channels: 5
• Core Size: 16 Bit
• Program Memory Size: 64 KB
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Embedded Interface Type: I2C, LIN, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

2.4
The program memory map extends from 000000h to
FFFFFEh. Code storage is located at the base of the
memory map and supports up to 22K instruction words
(about 64 Kbytes). Table 2-2 shows the program
memory size and number of erase and program blocks
present in each device variant. Each erase block, or
page, contains 512 instructions, and each program
block, or row, contains 64 instructions.
The last four implemented program memory locations
are reserved for the Flash Configuration Words. The
reserved addresses are also shown in Table 2-2.
TABLE 2-2:
© 2009 Microchip Technology Inc.
PIC24FJ32GA10X
PIC24FJ32GB00X
PIC24FJ64GA10X
PIC24FJ64GB00X
Device
Memory Map
CODE MEMORY SIZE AND FLASH CONFIGURATION WORD LOCATIONS FOR
PIC24FJ64GA1/GB0 DEVICES
(Instruction Words)
00ABFEh (22K)
Address Limit
0057FEh (11K)
User Memory
Blocks
Write
176
344
Blocks
Erase
22
43
Locations, 800000h through 8007FEh, are reserved for
executive code memory. This region stores the
programming executive and the debugging executive.
The programming executive is used for device
programming and the debugging executive is used for
in-circuit debugging. This region of memory can not be
used to store user code.
Locations, FF0000h and FF0002h, are reserved for the
Device ID registers. These bits can be used by the
programmer to identify what device type is being
programmed. They are described in Section 6.1
“Device ID”. The Device ID registers read out
normally, even after code protection is applied.
Figure 2-7
PIC24FJ64GA1/GB0 family variants.
PIC24FJ64GA1/GB0
00ABFEh
0057FEh
1
shows
Configuration Word Addresses
00ABFCh
0057FCh
the
2
memory
00ABFAh
0057FAh
3
DS39934B-page 7
map
00ABF8h
0057F8h
for
4
the