XR16L570IL24-F Exar Corporation, XR16L570IL24-F Datasheet - Page 29

• Manufacturer Part Number: XR16L570IL24-F
• Description: 2.25 To 5.5V W/ 5V TOLERANT INPUT UART W/16 BYTE FIFO W/ POWER SAVE
• Manufacturer: Exar Corporation

Specifications of XR16L570IL24-F

• Features: *
• Number Of Channels: 1, UART
• Fifo's: 16 Byte
• Protocol: RS232, RS422
• Voltage - Supply: 1.62 V ~ 5.5 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 24-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REV. 1.0.1
MCR[4]: Internal Loopback Enable
•
•
MCR[5]: Xon-Any Enable
•
•
MCR[6]: Infrared Encoder/Decoder Enable
•
•
MCR[7]: BRG Clock Prescaler Select
•
•
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
•
•
LSR[1]: Receiver Overrun Flag
•
•
LSR[2]: Receive Data Parity Error Flag
•
•
LSR[3]: Receive Data Framing Error Flag
•
•
4.9
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the L570 is programmed to use the Xon/Xoff flow control.
Logic 0 = Enable the standard modem receive and transmit input/output interface (default).
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. While in this mode, the infrared TX output will be a logic 0 during idle data conditions.
Logic 0 = Divide by one. The input clock from the external clock is fed directly to the Programmable Baud
Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the external clock by four and feeds it to
the Programmable Baud Rate Generator, hence, data rates get reduced 4 times.
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
Line Status Register (LSR) - Read Only
SMALLEST 1.62V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
29
Figure
13.
XR16L570