EPM7256AETC100-5N Altera, EPM7256AETC100-5N Datasheet - Page 16

• Manufacturer Part Number: EPM7256AETC100-5N
• Description: IC MAX 7000 CPLD 256 100-TQFP
• Manufacturer: Altera
• Series: MAX® 7000Ar

Specifications of EPM7256AETC100-5N

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 5.5ns
• Voltage Supply - Internal: 3 V ~ 3.6 V
• Number Of Logic Elements/blocks: 16
• Number Of Macrocells: 256
• Number Of Gates: 5000
• Number Of I /o: 84
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-TQFP, 100-VQFP
• Voltage: 3.3V
• Memory Type: EEPROM
• Number Of Logic Elements/cells: 16
• Family Name: MAX 7000A
• # Macrocells: 256
• Number Of Usable Gates: 5000
• Frequency (max): 250MHz
• Propagation Delay Time: 5.5ns
• Number Of Logic Blocks/elements: 16
• # I/os (max): 84
• Operating Supply Voltage (typ): 3.3V
• In System Programmable: Yes
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Compliant

MAX 7000A Programmable Logic Device Data Sheet
In-System
Programma-
bility
16
MAX 7000A devices can be programmed in-system via an industry-
standard 4-pin IEEE Std. 1149.1 (JTAG) interface. ISP offers quick, efficient
iterations during design development and debugging cycles. The
MAX 7000A architecture internally generates the high programming
voltages required to program EEPROM cells, allowing in-system
programming with only a single 3.3-V power supply. During in-system
programming, the I/O pins are tri-stated and weakly pulled-up to
eliminate board conflicts. The pull-up value is nominally 50 kΩ.
MAX 7000AE devices have an enhanced ISP algorithm for faster
programming. These devices also offer an ISP_Done bit that provides safe
operation when in-system programming is interrupted. This ISP_Done
bit, which is the last bit programmed, prevents all I/O pins from driving
until the bit is programmed. This feature is only available in EPM7032AE,
EPM7064AE, EPM7128AE, EPM7256AE, and EPM7512AE devices.
ISP simplifies the manufacturing flow by allowing devices to be mounted
on a PCB with standard pick-and-place equipment before they are
programmed. MAX 7000A devices can be programmed by downloading
the information via in-circuit testers, embedded processors, the Altera
MasterBlaster serial/USB communications cable, ByteBlasterMV parallel
port download cable, and BitBlaster serial download cable. Programming
the devices after they are placed on the board eliminates lead damage on
high-pin-count packages (e.g., QFP packages) due to device handling.
MAX 7000A devices can be reprogrammed after a system has already
shipped to the field. For example, product upgrades can be performed in
the field via software or modem.
In-system programming can be accomplished with either an adaptive or
constant algorithm. An adaptive algorithm reads information from the
unit and adapts subsequent programming steps to achieve the fastest
possible programming time for that unit. A constant algorithm uses a pre-
defined (non-adaptive) programming sequence that does not take
advantage of adaptive algorithm programming time improvements.
Some in-circuit testers cannot program using an adaptive algorithm.
Therefore, a constant algorithm must be used. MAX 7000AE devices can
be programmed with either an adaptive or constant (non-adaptive)
algorithm. EPM7128A and EPM7256A device can only be programmed
with an adaptive algorithm; users programming these two devices on
platforms that cannot use an adaptive algorithm should use EPM7128AE
and EPM7256AE devices.
The Jam Standard Test and Programming Language (STAPL), JEDEC
standard JESD 71, can be used to program MAX 7000A devices with in-
circuit testers, PCs, or embedded processors.
Altera Corporation