ATmega329P Atmel Corporation, ATmega329P Datasheet - Page 312

• Manufacturer Part Number: ATmega329P
• Manufacturer: Atmel Corporation

Specifications of ATmega329P

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.7.16
27.7.17
8021G–AVR–03/11
Serial Programming Pin Mapping
Serial Programming Algorithm
Table 27-16. Pin Mapping Serial Programming
Figure 27-10. Serial Programming and Verify
Notes:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
When writing serial data to the ATmega329P/3290P, data is clocked on the rising edge of SCK.
When reading data from the ATmega329P/3290P, data is clocked on the falling edge of SCK.
See
To program and verify the ATmega329P/3290P in the serial programming mode, the following
sequence is recommended (See four byte instruction formats in
1. Power-up sequence:
Apply power between V
Figure 27-11
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
Symbol
MOSI
MISO
SCK
XTAL1 pin.
CC
- 0.3V < AVCC < V
for timing details.
CC
and GND while RESET and SCK are set to “0”. In some sys-
Pins
PB2
PB3
PB1
ck
ck
CC
MOSI
MISO
< 12MHz, 3 CPU clock cycles for f
< 12MHz, 3 CPU clock cycles for f
SCK
+ 0.3V, however, AVCC should always be within 1.8 - 5.5V
XTAL1
RESET
GND
(1)
I/O
O
I
I
AVCC
VCC
+1.8 - 5.5V
+1.8 - 5.5V
ATmega329P/3290P
(2)
Table
ck
ck
Serial Data out
Serial Data in
Description
27-18):
Serial Clock
>= 12MHz
>= 12MHz
312