SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 767

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.5.4
Name:
Access Type:
• SPEED: Speed Status
0 = reset by hardware when the hardware is in Full Speed mode.
1 = set by hardware when the hardware is in High Speed mode
• DET_SUSPD: Suspend Interrupt
0 = cleared by setting the DET_SUSPD bit in UDPHS_CLRINT register
1 = set by hardware when a UDPHS Suspend (Idle bus for three frame periods, a J state for 3 ms) is detected. This triggers
a UDPHS interrupt when the DET_SUSPD bit is set in UDPHS_IEN register.
• MICRO_SOF: Micro Start Of Frame Interrupt
0 = cleared by setting the MICRO_SOF bit in UDPHS_CLRINT register.
1 = set by hardware when an UDPHS micro start of frame PID (SOF) has been detected (every 125 us) or synthesized by
the macro. This triggers a UDPHS interrupt when the MICRO_SOF bit is set in UDPHS_IEN. In case of detected SOF, the
MICRO_FRAME_NUM field in UDPHS_FNUM register is incremented and the FRAME_NUMBER field doesn’t change.
Note:
• INT_SOF: Start Of Frame Interrupt
0 = cleared by setting the INT_SOF bit in UDPHS_CLRINT.
1 = set by hardware when an UDPHS Start Of Frame PID (SOF) has been detected (every 1 ms) or synthesized by the
macro. This triggers a UDPHS interrupt when the INT_SOF bit is set in UDPHS_IEN register. In case of detected SOF, in
High Speed mode, the MICRO_FRAME_NUMBER field is cleared in UDPHS_FNUM register and the FRAME_NUMBER
field is updated.
• ENDRESET: End Of Reset Interrupt
0 = cleared by setting the ENDRESET bit in UDPHS_CLRINT.
1 = set by hardware when an End Of Reset has been detected by the UDPHS controller. This triggers a UDPHS interrupt
when the ENDRESET bit is set in UDPHS_IEN.
6289D–ATARM–3-Oct-11
UPSTR_RES
31
23
15
–
–
–
7
The Micro Start Of Frame Interrupt (MICRO_SOF), and the Start Of Frame Interrupt (INT_SOF) are not generated at the same
time.
UDPHS Interrupt Status Register
ENDOFRSM
DMA_6
EPT_6
30
22
14
UDPHS_INTSTA
Read-only
–
6
WAKE_UP
DMA_5
EPT_5
29
21
13
–
5
ENDRESET
DMA_4
EPT_4
28
20
12
–
4
INT_SOF
DMA_3
EPT_3
27
19
11
–
3
MICRO_SOF
DMA_2
EPT_2
AT91SAM9R64/RL64
26
18
10
–
2
DET_SUSPD
DMA_1
EPT_1
25
17
–
9
1
SPEED
EPT_0
24
16
–
–
8
0
767