SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 469

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.9.4.2
33.9.4.3
33.9.4.4
33.9.4.5
33.9.5
33.9.5.1
469
AT91SAM9XE128/256/512 Preliminary
Data Transfer
Write Sequence
Clock Synchronization Sequence
General Call
PDC
Read Operation
Note that a STOP or a repeated START always follows a NACK.
See
In the case of a Write sequence (SVREAD is low), the RXRDY (Receive Holding Register
Ready) flag is set as soon as a character has been received in the TWI_RHR (TWI Receive
Holding Register). RXRDY is reset when reading the TWI_RHR.
TWI continues receiving data until a STOP condition or a REPEATED_START + an address dif-
ferent from SADR is detected. Note that at the end of the write sequence TXCOMP flag is set
and SVACC reset.
See
In the case where TWI_THR or TWI_RHR is not written/read in time, TWI performs a clock
synchronization.
Clock stretching information is given by the SCLWS (Clock Wait state) bit.
See
In the case where a GENERAL CALL is performed, GACC (General Call ACCess) flag is set.
After GACC is set, it is up to the programmer to interpret the meaning of the GENERAL CALL
and to decode the new address programming sequence.
See
As it is impossible to know the exact number of data to receive/send, the use of PDC is NOT rec-
ommended in SLAVE mode.
The read mode is defined as a data requirement from the master.
After a START or a REPEATED START condition is detected, the decoding of the address
starts. If the slave address (SADR) is decoded, SVACC is set and SVREAD indicates the direc-
tion of the transfer.
Until a STOP or REPEATED START condition is detected, TWI continues sending data loaded
in the TWI_THR register.
If a STOP condition or a REPEATED START + an address different from SADR is detected,
SVACC is reset.
Figure 33-25 on page 470
Figure 33-25 on page
Figure 33-26 on page
Figure 33-28 on page 472
Figure 33-27 on page
describes the write operation.
470.
470.
471.
and
Figure 33-29 on page
473.
6254C–ATARM–22-Jan-10