XA-G39 NXP Semiconductors, XA-G39 Datasheet - Page 5

• Manufacturer Part Number: XA-G39
• Description: Xa 16-bit Microcontroller Family Xa 16-bit Microcontroller 32k Flash/1k Ram, Watchdog, 2 Uarts
• Manufacturer: NXP Semiconductors

Philips Semiconductors
PIN DESCRIPTION
2002 Mar 13
MNEMONIC
P0.0 – P0.7
P1.0 – P1.7
P2.0 – P2.7
P3.0 – P3.7
XA 16-bit microcontroller family
32K Flash/1K RAM, watchdog, 2 UARTs
RST
ALE
V
V
SS
DD
23, 44
43–36
24–31
13–19
1, 22
PIN
NO.
2–9
11,
11
13
14
15
16
17
18
19
10
33
2
3
4
5
6
7
8
9
TYPE
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
When the external program/data bus is used, Port 0 becomes the multiplexed low data/instruction byte and
Address Latch Enable: A high output on the ALE pin signals external circuitry to latch the address portion
Ground: 0 V reference.
Power Supply: This is the power supply voltage for normal, idle, and power down operation.
Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. Port 0 latches have 1s written to
them and are configured in the quasi-bidirectional mode during reset. The operation of port 0 pins as
inputs and outputs depends upon the port configuration selected. Each port pin is configured
independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for
details.
address lines 4 through 11.
Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type. Port 1 latches have 1s written to
them and are configured in the quasi-bidirectional mode during reset. The operation of port 1 pins as
inputs and outputs depends upon the port configuration selected. Each port pin is configured
independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for
details.
Port 1 also provides special functions as described below.
Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. Port 2 latches have 1s written to
them and are configured in the quasi-bidirectional mode during reset. The operation of port 2 pins as
inputs and outputs depends upon the port configuration selected. Each port pin is configured
independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for
details.
When the external program/data bus is used in 16-bit mode, Port 2 becomes the multiplexed high
data/instruction byte and address lines 12 through 19. When the external program/data bus is used in 8-bit
mode, the number of address lines that appear on port 2 is user programmable.
Port 3: Port 3 is an 8-bit I/O port with a user configurable output type. Port 3 latches have 1s written to
them and are configured in the quasi-bidirectional mode during reset. the operation of port 3 pins as inputs
and outputs depends upon the port configuration selected. Each port pin is configured independently.
Refer to the section on I/O port configuration and the DC Electrical Characteristics for details.
Port 3 also provides various special functions as described below.
Reset: A low on this pin resets the microcontroller, causing I/O ports and peripherals to take on their
default states, and the processor to begin execution at the address contained in the reset vector. Refer to
the section on Reset for details.
of the multiplexed address/data bus. A pulse on ALE occurs only when it is needed in order to process a
bus cycle.
A0/WRH:
A1:
A2:
A3:
RxD1 (P1.4):
TxD1 (P1.5):
T2 (P1.6):
T2EX (P1.7):
RxD0 (P3.0):
TxD0 (P3.1):
INT0 (P3.2):
INT1 (P3.3):
T0 (P3.4):
T1/BUSW (P3.5):
WRL (P3.6):
RD (P3.7):
Address bit 0 of the external address bus when the external data bus is configured for
an 8 bit width. When the external data bus is configured for a 16 bit width, this pin
becomes the high byte write strobe.
Address bit 1 of the external address bus.
Address bit 2 of the external address bus.
Address bit 3 of the external address bus.
Receiver input for serial port 1.
Transmitter output for serial port 1.
Timer/counter 2 external count input/clockout.
Timer/counter 2 reload/capture/direction control
Receiver input for serial port 0.
Transmitter output for serial port 0.
External interrupt 0 input.
External interrupt 1 input.
Timer 0 external input, or timer 0 overflow output.
Timer 1 external input, or timer 1 overflow output. The value on this pin is latched
as the external reset input is released and defines the default external data bus
width (BUSW). 0 = 8-bit bus and 1 = 16-bit bus.
External data memory low byte write strobe.
External data memory read strobe.
5
NAME AND FUNCTION
XA-G39
Preliminary data