KSZ8893-MQL Micrel Semiconductor, Inc., KSZ8893-MQL Datasheet - Page 14
KSZ8893-MQL
Manufacturer Part Number
KSZ8893-MQL
Description
Integrated 3-Port 10/100 Managed Switch with PHYs
Manufacturer
Micrel Semiconductor, Inc.
Datasheet
1.KSZ8893-MQL.pdf
(106 pages)
- Current page: 14 of 106
- Download datasheet (508Kb)
Micrel
November 2005
Note:
1. P = Power supply.
Pin Number
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Ipd = Input w/ internal pull-down.
Opd = Output w/ internal pull-down.
Gnd = Ground.
I = Input.
Ipu = Input w/ internal pull-up.
Pin Name
RMII_EN
HWPOVR
P2MDIXDIS
P2MDIX
P1ANEN
P1SPD
P1DPX
P1FFC
NC
NC
PWRDN
AGND
VDDA
AGND
MUX1
MUX2
Type
Opd
Ipd
Ipd
Ipd
Ipu
Ipd
Ipd
Ipd
Ipd
Ipd
Ipu
Gnd
P
Gnd
I
I
(1)
14
Description
Strap pin for RMII Mode
0 = Disable
1 = Enable
After reset, this pin has no meaning and is a no connect.
Hardware pin overwrite
0 = Disable. All strap-in pins configurations are overwritten by
the EEPROM configuration data
1 = Enable. All strap-in pins configurations are overwritten by
the EEPROM configuration data, except for register 0x2C bits
[7:5], (port 2: auto-negotiation enable, force speed, force
duplex).
Port 2 Auto MDI/MDI-X
PD (default) = enable
PU = disable
Port 2 MDI/MDI-X setting when auto MDI/MDI-X is disabled.
PD (default) = MDI-X (transmit on TXP2 / TXM2 pins)
PU = MDI, (transmit on RXP2 / RXM2 pins)
1 = enable auto-negotiation on port 1
0 = disable auto-negotiation on port 1
1 = force port 1 to 100BT if P1ANEN = 0
0 = force port 1 to 10BT if P1ANEN = 0
1 = port 1 default to full duplex mode if P1ANEN = 1 and auto-
negotiation fails. Force port 1 in full-duplex mode if P1ANEN
= 0.
0 = port 1 default to half duplex mode if P1ANEN = 1 and
auto- negotiation fails. Force port 1 in half duplex mode if
P1ANEN = 0.
1 = always enable (force) port 1 flow control feature
0 = port 1 flow control feature enable is determined by auto
negotiation result.
No connect
No connect
Chip power down input (active low)
Analog ground
1.2V analog V
Analog ground
Factory test pin - float for normal operation
Factory test pin - float for normal operation
DD
KSZ8893MQL/MQLI
M9999-111705
Related parts for KSZ8893-MQL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
UCAP NEGATIVE LOW DROPOUT REGULATOR
Manufacturer:
Micrel Semiconductor, Inc.
Part Number:
Description:
1.8V, 3.3V 10/100BASE-T/TX/F Physical Layer Transceiver
Manufacturer:
Micrel Semiconductor, Inc.
Datasheet:
Part Number:
Description:
IC PHY 1CH 10/100MBPS 48LQFP T/R
Manufacturer:
Micrel Semiconductor, Inc.
Part Number:
Description:
IC PHY 1CH 10/100MBPS 48LQFP T/R
Manufacturer:
Micrel Semiconductor, Inc.
Datasheet:
Part Number:
Description:
Ethernet MAC Controller with PCI Interface2 pages, 163.24 KbOriginal
Manufacturer:
Micrel Semiconductor, Inc.
Part Number:
Description:
2-Port Ethernet Switch with PCI Interface
Manufacturer:
Micrel Semiconductor, Inc.
Part Number:
Description:
Single Port MAC/PHY Controller with Non PCI Interface
Manufacturer:
Micrel Semiconductor, Inc.
Part Number:
Description:
UCAP NEGATIVE LOW DROPOUT REGULATOR
Manufacturer:
Micrel Semiconductor, Inc.