xr16m698 Exar Corporation, xr16m698 Datasheet - Page 9

• Manufacturer Part Number: xr16m698
• Description: 1.62v To 3.63v High Performance Octal Uart With 32-byte Fifo
• Manufacturer: Exar Corporation

REV. 1.0.0
The 698 includes an on-chip oscillator. The crystal oscillator provides the system clock to the Baud Rate
Generators (BRG) in each of the 8 UARTs, the 16-bit general purpose timer/counter and internal logics. XTAL1
is the input to the oscillator or external clock buffer input with XTAL2 pin being the output. For programming
details, see
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see
clock can be connected to the XTAL1 pin to clock the internal 8 baud rate generators for standard or custom
rates. The typical oscillator connections are shown in
see application note DAN108 on EXAR’s web site.
Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The
prescaler is controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide
the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further
divides this clock by a programmable divisor between 1 and (2
obtain a 16X or 8X or 4X sampling clock of the serial data rate. The sampling clock is used by the transmitter
for data bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to
the value of ’1’ (DLL = 0x01, DLM = 0x00 and DLD = 0x00) upon reset. Therefore, the BRG must be
programmed during initialization to the operating data rate. The DLL and DLM registers provide the integer part
of the divisor and the DLD register provides the fractional part of the dvisior. Only the four lower bits of the DLD
are implemented and they are used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting
1111). Programming the Baud Rate Generator Registers DLL, DLM and DLD provides the capability for
selecting the operating data rate.
external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times
less than that shown in
sampling mode, please note that the bit-time will have a jitter (+/- 1/16) whenever the DLD is non-zero and is
an odd number. At 4X sampling rate, these data rates would quadruple. When using a non-standard data rate
crystal or external clock, the divisor value can be calculated with the following equation(s):
2.5
2.6
Crystal Oscillator
Programmable Baud Rate Generator with Fractional Divisor
“Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on page
Table
F
IGURE
1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
5. At 8X sampling rate, these data rates would double. Also, when using 8X
Table 5
3. T
YPICAL OSCILLATOR CONNECTIONS
22-47pF
XTAL1
shows the standard data rates available with a 24MHz crystal or
C1
R=300K to 400K
24 MHz
Figure
9
3. For further reading on oscillator circuit please
22-47pF
XTAL2
16
C2
- 0.0625) in increments of 0.0625 (1/16) to
Figure
3). Alternatively, an external
XR16M698
9.