ADUC847BCP8-5 AD [Analog Devices], ADUC847BCP8-5 Datasheet - Page 80
ADUC847BCP8-5
Manufacturer Part Number
ADUC847BCP8-5
Description
MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
Manufacturer
AD [Analog Devices]
Datasheet
1.ADUC847BCP8-5.pdf
(108 pages)
- Current page: 80 of 108
- Download datasheet (2Mb)
ADuC845/ADuC847/ADuC848
UART SERIAL INTERFACE
The serial port is full duplex, meaning that it can transmit and
receive simultaneously. It is also receive buffered, meaning that
it can begin receiving a second byte before a previously received
byte is read from the receive register. However, if the first byte is
still not read by the time reception of the second byte is complete,
the first byte is lost. The physical interface to the serial data
network is via Pins RxD(P3.0) and TxD(P3.1), while the SFR
interface to the UART comprises SBUF and SCON, as described
below.
Table 54. SCON SFR Bit Designations
Bit No.
7, 6
5
4
3
2
1
0
SBUF—UART Serial Port Data Register
SFR Address:
Power-On Default:
Bit Addressable:
Name
SM0, SM1
SM2
REN
TB8
RB8
TI
RI
99H
00H
No
Description
UART Serial Mode Select Bits. These bits select the serial port operating mode as follows:
SM0
0
0
1
1
Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3.
In Mode 0, SM2 should be cleared.
In Mode 1, if SM2 is set, RI is not activated if a valid stop bit was not received. If SM2 is cleared, RI is set as soon as
the byte of data is received.
In Modes 2 or 3, if SM2 is set, RI is not activated if the received ninth data bit in RB8 is 0.
If SM2 is cleared, RI is set as soon as the byte of data is received.
Serial Port Receive Enable Bit.
Set by user software to enable serial port reception.
Serial Port Transmit (Bit 9).
The data loaded into TB8 is the ninth data bit transmitted in Modes 2 and 3. Cleared by user software to disable
serial port reception.
Serial Port Receiver Bit 9.
The ninth data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8.
Serial Port Transmit Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or at the beginning of the stop bit in Modes 1, 2, and 3.
TI must be cleared by user software.
Serial Port Receive Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or halfway through the stop bit in Modes 1, 2, and 3.
RI must be cleared by software.
SM1
0
1
0
1
Selected Operating Mode.
Mode 0: Shift register, fixed baud rate (Core_Clk/2).
Mode 1: 8-bit UART, variable baud rate.
Mode 2: 9-bit UART, fixed baud rate (Core_Clk/32) or (Core_Clk/16).
Mode 3: 9-bit UART, variable baud rate.
Rev. A | Page 80 of 108
SBUF SFR
Both the serial port receive and transmit registers are accessed
through the SBUF SFR (SFR address = 99H). Writing to SBUF
loads the transmit register, and reading SBUF accesses a
physically separate receive register.
SCON UART—Serial Port Control Register
SFR Address:
Power-On Default:
Bit Addressable:
98H
00H
Yes
Related parts for ADUC847BCP8-5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DPG2 EVAL ADAPTER FOR XILINX BOARDS
Manufacturer:
Analog Devices Inc
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
RF Development Tools Sransceiver board for FMC evaluation kit
Manufacturer:
Analog Devices
Part Number:
Description:
Analog Devices: Data Converters: DAC 12-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Analog Devices: Data Converters: DAC 8-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Low-Power Analog Front End with DSP Microcomputer
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
2 Pair/1 Pair ETSI Compatible HDSL Analog Front End
Manufacturer:
AD [Analog Devices]
Datasheet: