FAN103_10 FAIRCHILD [Fairchild Semiconductor], FAN103_10 Datasheet

no-image

FAN103_10

Manufacturer Part Number
FAN103_10
Description
Primary-Side-Regulation PWM Controller (PWM-PSR)
Manufacturer
FAIRCHILD [Fairchild Semiconductor]
Datasheet
© 2010 Fairchild Semiconductor Corporation
FAN103 • Rev. 1.0.3
FAN103
Primary-Side-Regulation PWM Controller (PWM-PSR)
Features
Applications
Ordering Information
Part Number
FAN103MY
For Fairchild’s definition of Eco Status, please visit:
Low Standby Power Under 30mW
High Voltage Startup
Fewest External Component Counts
Constant-Voltage (CV) and Constant-Current (CC)
Control without Secondary-Feedback Circuitry
Green-Mode Function: Linearly-Decreasing PWM
Frequency
Fixed PWM Frequency at 50kHz with Frequency
Hopping to Solve EMI Problem
Cable Compensation in CV Mode
Peak-Current-Mode Control in CV Mode
Cycle-by-Cycle Current Limiting
V
V
Gate Output Maximum Voltage Clamped at 15V
Fixed Over-Temperature Protection with
Auto Restart
Available in the 8-Lead SOP Package
Battery chargers for cellular phones, cordless
phones, PDA, digital cameras, power tools, etc.
Replaces linear transformer and RCC SMPS
DD
DD
Over-Voltage Protection with Auto Restart
Under-Voltage Lockout (UVLO)
Temperature Range
-40°C to +105°C
Operating
Status
Green
Eco
http://www.fairchildsemi.com/company/green/rohs_green.html
8-Lead, Small Outline Package (SOP-8)
Description
This third-generation Primary-Side-Regulation (PSR)
and highly integrated PWM controller provides several
features to enhance the performance of low-power
flyback
TURECURRENT™, of FAN103 enables precise CC
regulation and simplified circuit for battery charger
applications. A low-cost, smaller and lighter charger
results as compared to a conventional design or a linear
transformer.
To
proprietary green-mode
modulation to linearly decrease PWM frequency under
light-load conditions. This green mode assists the power
supply in meeting the power conservation requirement.
By using the FAN103, a charger can be implemented
with few external components and minimized cost. A
typical output CV/CC characteristic envelope is shown
in Figure 1.
V
Figure 1. Typical Output V-I Characteristic
O
minimize
Package
converters.
standby
The
function
power
Before Cable Compensation
After Cable Compensation
Maximum
Minimum
proprietary
Packing Method
consumption,
provides off-time
Tape & Reel
March 2010
www.fairchildsemi.com
topology,
I
O
the

Related parts for FAN103_10

FAN103_10 Summary of contents

Page 1

FAN103 Primary-Side-Regulation PWM Controller (PWM-PSR) Features Low Standby Power Under 30mW High Voltage Startup Fewest External Component Counts Constant-Voltage (CV) and Constant-Current (CC) Control without Secondary-Feedback Circuitry Green-Mode Function: Linearly-Decreasing PWM Frequency Fixed PWM Frequency at 50kHz with Frequency Hopping ...

Page 2

Application Diagram Input Internal Block Diagram © 2010 Fairchild Semiconductor Corporation FAN103 • Rev. 1.0 sn2 sn1 D ...

Page 3

Marking Information Pin Configuration Pin Definitions Pin # Name Description Current Sense. This pin connects a current sense resistor, to detect the MOSFET current for 1 CS peak-current-mode control in CV mode, and provides the output-current regulation in CC mode. ...

Page 4

Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure ...

Page 5

Electrical Characteristics Unless otherwise specified Symbol Parameter V Section DD V Continuously Operating Voltage OP V Turn-On Threshold Voltage DD-ON V Turn-Off Threshold Voltage DD-OFF I Operating Current DD-OP I Green-Mode Operating Supply Current DD-GREEN V V Over-Voltage ...

Page 6

Electrical Characteristics Unless otherwise specified Symbol Parameter Current-Error-Amplifier Section V Reference Voltage IR Cable Compensation Section V COMR Pin for Cable Compensation COMR Gate Section DCY Maximum Duty Cycle MAX V Output Voltage Low OL V Output Voltage ...

Page 7

Typical Performance Characteristics 17 16.6 16.2 15.8 15.4 15 -40 -30 - Temperature (ºC) Figure 6. Turn-On Threshold Voltage (V vs. Temperature 5 4.2 3.4 2.6 1.8 1 -40 -30 - Temperature (ºC) Figure 8. Operating ...

Page 8

Typical Performance Characteristics 450 420 390 360 330 300 -40 -30 - Temperature (ºC) Figure 12. Minimum Frequency at No Load (f ) vs. Temperature OSC-N-MIN 3 2.5 2 1.5 1 0.5 0 -40 -30 - ...

Page 9

Typical Performance Characteristics Figure 19. Output Clamp Voltage (V Figure 20. Variation Test Voltage on COMR Pin for Cable Compensation (V © 2010 Fairchild Semiconductor Corporation FAN103 • Rev. 1.0.3 12 11.2 10.4 9.6 8.8 8 -40 -30 -15 0 ...

Page 10

Functional Description Figure 21 shows the basic circuit diagram of a primary- side regulated flyback converter with typical waveforms shown in Figure 22. Generally, conduction mode (DCM) operation is preferred for primary-side regulation since it allows better output regulation. The ...

Page 11

Cable Voltage Drop Compensation When it comes to cellular phone charger applications, the battery is located at the end of cable, which causes, typically, several percentage of voltage drop on the actual battery voltage. FAN103 has a built-in cable voltage ...

Page 12

Under-Voltage Lockout (UVLO) The turn-on and turn-off thresholds are fixed internally at 16V and 5V, respectively. During startup, the hold-up capacitor must be charged to 16V through the startup resistor to enable the FAN103. The hold-up capacitor continues to supply ...

Page 13

Typical Application Circuit (Primary-Side-Regulated Flyback Charger) Application Fairchild Devices Cell Phone Charger FAN103 Features High efficiency (>68.17% at Full Load) Meeting EPS 2.0 Regulation with Enough Margin Low standby (Pin <30mW at No Load Condition) Tight output regulation (CV: ±5%, ...

Page 14

Typical Application Circuit Transformer Specification Core: EE16 Bobbin: EE16 Notes: 4. When W4R’s winding is reversed winding, it must wind one layer. 5. When W2 is winding, put 1 layer tape after wind first layer. TERMINAL ...

Page 15

Physical Dimensions 8 6.20 5.80 1 PIN ONE INDICATOR (0.33) 0.25 0.10 1.75 MAX R0.10 R0.10 8° 0° 0.90 0.406 DETAIL A Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner ...

Page 16

Fairchild Semiconductor Corporation FAN103 • Rev. 1.0.3 16 www.fairchildsemi.com ...

Related keywords