LTC3719EG Linear Technology, LTC3719EG Datasheet - Page 15

• Manufacturer Part Number: LTC3719EG
• Description: IC SW REG SYNC STEP-DOWN 36-SSOP
• Manufacturer: Linear Technology

Specifications of LTC3719EG

• Applications: Controller, AMD Opteron™
• Voltage - Input: 4 ~ 36 V
• Number Of Outputs: 1
• Voltage - Output: 0.8 ~ 1.55 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIO S I FOR ATIO
LTC3719 is operating in continuous mode the duty factors
for the top and bottom MOSFETs of each output stage are
given by:
The MOSFET power dissipations at maximum output
current are given by:
where is the temperature dependency of R
is a constant inversely related to the gate drive current.
Both MOSFETs have I
equation includes an additional term for transition losses,
which peak at the highest input voltage. For V
high current efficiency generally improves with larger
MOSFETs, while for V
increase to the point that the use of a higher R
with lower C
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during a
short-circuit when the synchronous switch is on close to
100% of the period.
The term (1 + ) is generally given for a MOSFET in the
form of a normalized R
voltage MOSFETs. C
MOSFET characteristics. The constant k = 1.7 can be
used to estimate the contributions of the two terms in the
main switch dissipation equation.
= 0.005/ C can be used as an approximation for low
P
P
Main Switch Duty Cycle
Synchronous Switch Duty Cycle
MAIN
SYNC
k V
V
V
V
OUT
RSS
IN
IN
IN
–
V
2
IN
V
actual provides higher efficiency. The
I
OUT
I
U
MAX
MAX
2
2
IN
2
R losses but the topside N-channel
RSS
> 20V the transition losses rapidly
DS(ON)
I
2
MAX
U
C
2
1
is usually specified in the
RSS
vs temperature curve, but
V
2
V
OUT
IN
R
1
f
DS ON
W
(
R
V
)
DS ON
IN
(
DS(ON)
–
DS(ON)
V
IN
IN
V
)
U
< 20V the
OUT
device
and k
The Schottky diodes, D1 and D2 shown in Figure 1
conduct during the dead-time between the conduction of
the two large power MOSFETs. This helps prevent the
body diode of the bottom MOSFET from turning on,
storing charge during the dead-time, and requiring a
reverse recovery period which would reduce efficiency. A
1A to 3A Schottky (depending on output current) diode is
generally a good compromise for both regions of opera-
tion due to the relatively small average current. Larger
diodes result in additional transition losses due to their
larger junction capacitance.
C
In continuous mode, the source current of each top
N-channel MOSFET is a square wave of duty cycle V
V
RMS current must be used. The details of a closed form
equation can be found in Application Note 77. Figure 4
shows the input capacitor ripple current for a 2-phase
configuration with the output voltage fixed and input
voltage varied. The input ripple current is normalized
against the DC output current. The graph can be used in
place of tedious calculations. The minimum input ripple
current can be achieved when the input voltage is twice the
output voltage.
In the graph of Figure 4, the 2-phase local maximum input
RMS capacitor currents are reached when:
where k = 1, 2
These worst-case conditions are commonly used for
design because even significant deviations do not offer
much relief. Note that capacitor manufacturer’s ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to
meet size or height requirements in the design. Always
consult the capacitor manufacturer if there is any
question.
IN
IN
. A low ESR input capacitor sized for the maximum
V
and C
V
OUT
IN
OUT
2
k
Selection
4
1
LTC3719
sn3719 3719fs
15
OUT
/