MAX1402EVKIT Maxim Integrated Products, MAX1402EVKIT Datasheet - Page 11

• Manufacturer Part Number: MAX1402EVKIT
• Description: EVAL KIT FOR MAX1402
• Manufacturer: Maxim Integrated Products

Specifications of MAX1402EVKIT

• Number Of Adc's: 1
• Number Of Bits: 18
• Sampling Rate (per Second): 480
• Data Interface: Serial
• Inputs Per Adc: 6 Single Ended
• Input Range: ±VREF/2
• Power (typ) @ Conditions: 26.7mW @ 480SPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: 0°C ~ 70°C
• Utilized Ic / Part: MAX1402
• Interface Type: SMA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: MAX1402

PIN
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
CLKOUT
RESET
NAME
CLKIN
AGND
OUT2
OUT1
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
DS1
DS0
CS
V+
______________________________________________________________________________________
Clock Input. A crystal can be connected across CLKIN and CLKOUT. Alternatively, drive CLKIN with a
CMOS-compatible clock at a nominal frequency of 2.4576MHz or 1.024MHz, and leave CLKOUT uncon-
nected. Frequencies of 4.9152MHz and 2.048MHz may be used if the X2CLK control bit is set to 1.
Clock Output. When deriving the master clock from a crystal, connect the crystal between CLKIN and
CLKOUT. In this mode, the on-chip clock signal is not available at CLKOUT. Leave CLKOUT unconnected
when CLKIN is driven with an external clock.
Chip-Select Input. Active-low logic input used to enable the digital interface. With CS hard-wired low, the
MAX1402 operates in its 3-wire interface mode with SCLK, DIN and DOUT used to interface to the device.
CS is used either to select the device in systems with more than one device on the serial bus, or as a
frame-synchronization signal for the MAX1402 when a continuous SCLK is used.
Active-Low Reset Input. Drive low to reset the control logic, interface logic, digital filter and analog modu-
lator to power-on status. RESET must be high and CLKIN must be toggling in order to exit reset.
Digital Input for Auxiliary Data Input Bit 1. The status of this bit is reflected in the output data by bit D4.
Used to communicate the status of DS1 via the serial interface.
Digital Input for Auxiliary Data Input Bit 0. The status of this bit is reflected in the output data by bit D3.
Used to communicate the status of DS0 via the serial interface.
Transducer Excitation Current Source 2
Transducer Excitation Current Source 1
Analog Ground. Reference point for the analog circuitry. AGND connects to the IC substrate.
Analog Positive Supply Voltage (+4.75V to +5.25V).
Analog Input Channel 1. May be used as a pseudo-differential input with AIN6 as common, or as the posi-
tive input of the AIN1/AIN2 differential analog input pair (see Communications Register section).
Analog Input Channel 2. May be used as a pseudo-differential input with AIN6 as common, or as the neg-
ative input of the AIN1/AIN2 differential analog input pair (see Communications Register section).
Analog Input Channel 3. May be used as a pseudo-differential input with AIN6 as common, or as the posi-
tive input of the AIN3/AIN4 differential analog input pair (see Communications Register section).
Analog Input Channel 4. May be used as a pseudo-differential input with AIN6 as common, or as the neg-
ative input of the AIN3/AIN4 differential analog input pair (see Communications Register section).
Analog Input Channel 5. Used as a differential or pseudo-differential input with AIN6
(see Communications Register section).
Analog Input 6. May be used as a common point for AIN1 through AIN5 in pseudo-differential mode, or as
the negative input of the AIN5/AIN6 differential analog input pair (see Communications Register section).
+5V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
FUNCTION
Pin Description
11