FPF2700 Fairchild Semiconductor, FPF2700 Datasheet

no-image

FPF2700

Manufacturer Part Number
FPF2700
Description
Manufacturer
Fairchild Semiconductor
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
FPF2700M
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
Part Number:
FPF2700MPX
Manufacturer:
NXP
Quantity:
2 000
Part Number:
FPF2700MPX
Manufacturer:
FAIRCHILD
Quantity:
8 000
Part Number:
FPF2700MPX
Manufacturer:
FSC
Quantity:
20 000
Part Number:
FPF2700MPX
0
Part Number:
FPF2700MX
Manufacturer:
FSC
Quantity:
20 000
Part Number:
FPF2700MX
0
Company:
Part Number:
FPF2700MX
Quantity:
14
Company:
Part Number:
FPF2700MX
Quantity:
5 000
© 2010 Fairchild Semiconductor Corporation
FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2
Figure 1. MLP (Top View) Figure 2. MLP (Bottom View)
FPF2700 / FPF2701 / FPF2702 — AccuPower™ 0.4~2A
Adjustable Over-Current Protection Load Switches
Features
Applications
Ordering Information
FPF2700MPX
FPF2701MPX
FPF2702MPX
FPF2700MX
FPF2701MX
FPF2702MX
Number
2.8V to 36V Input Voltage Range
Typical R
0.4A to 2A Adjustable Current Limit (Min.)
Slew Rate Controlled
ESD Protected, above 2000V HBM
Thermal Shutdown
Active LOW Enable
UVLO Protection
Power-Good Output
Motor Drives
Digital Cameras
Consumer Electronics
Industrial
Computing
Hard Disk Drives
Telecom Equipment
Part
DS(ON)
Figure 3. SO8 (Top View)
Current Limit [A]
=88m
0.4 – 2.0
0.4 – 2.0
0.4 – 2.0
0.4 – 2.0
0.4 – 2.0
0.4 – 2.0
Blanking Time [ms]
Current Limit
0.5
0.5
NA
0.5
0.5
NA
Description
The AccuPower™ FPF270X series is a family of
current-limit load switches that provide full protection to
systems and loads from excess current conditions.
Minimum current limit is adjustable from 0.4A to 2.0A.
The FPF270X contains a slew-rate-controlled N-channel
MOSFET and slew-rated turn-on to prevent power bus
disturbances from being caused by “hot plugging” loads
or momentary excess load demands. The input voltage
range is 2.8V to 36V. Loads can be activated or
deactivated with a low-voltage logic-compatible ON pin.
Fault conditions can be monitored using the error flag
pin and/or the power-good pin.
Each member of the FPF270X family serves a category
of load-fault response. All devices clamp the load
current so that it cannot exceed an externally
programmed current level. An over temperature feature
provides further device protection in case of excessive
levels of power dissipation.
FPF2700 responds to an overload condition that lasts
longer than a fixed blanking period by turning off the
load, followed by a retry after the auto-restart time.
FPF2701 responds to an overload condition that lasts
longer than a fixed blanking period by latching off the
load. The load remains off unless either the ON pin is
toggled or the input voltage cycles through UVLO.
FPF2702 is intended to be used with external fault
management. Like the FPF2700 and FPF2701, it sets
the fault signal pin LOW when it activates current
clamping. This device is intended for applications where
external fault management coordinates the overload
response with the FPF2702.
The FPF270X is available in a space-saving Pb and
Halogen free, 8-lead MLP 3x3mm and SO8 packages.
Auto-Restart
Time [ms]
127.5
127.5
NA
NA
NA
NA
Active LOW
Active LOW
Active LOW
Active LOW
Active LOW
Active LOW
Activity
ON Pin
January 2011
www.fairchildsemi.com
Package
MLP3X3
MLP3X3
MLP3X3
SO8
SO8
SO8

Related parts for FPF2700

FPF2700 Summary of contents

Page 1

... FPF2701MX 0.4 – 2.0 FPF2702MX 0.4 – 2.0 © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 Description The AccuPower™ FPF270X series is a family of current-limit load switches that provide full protection to systems and loads from excess current conditions. Minimum current limit is adjustable from 0.4A to 2.0A. ...

Page 2

... Application Diagram V IN 2.8V – 36V C IN Block Diagram © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 VIN VOUT OFF ON FLAGB ON ISET PGOOD R SET GND Figure 4. Typical Application Figure 5. Block Diagram 2 36V MAX. TO LOAD C OUT www.fairchildsemi.com ...

Page 3

... No connection. Leave open or connect to ground. Fault Output. Active LOW, open-drain output that indicates current limit, under-voltage FLAGB over -temperature state. 8 VOUT Switch Output. Output of the power switch. © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 1 VIN 1 VIN PGOOD 2 2 PGOOD ...

Page 4

... Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol V Input Supply Voltage IN T Ambient Operating Temperature A © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 Parameter (1) MLP 3x3 , See Figure 8 =25°C) A (1) SO8 , See Figure 10 ...

Page 5

... Rise Time R OUT t V Fall Time F OUT t Over-Current Blanking Time BLANK t Auto-Restart Time RESTART t Current-Limit Response Time CLR © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 =12V and T IN Conditions V =12V, V =0V OUT V =36V, V =3.3V OUT T =25° ...

Page 6

... V = 0V ON 120 110 100 Supply Voltage (V) Figure 15. Quiescent Current vs. Supply Voltage (ON) Figure 16. Quiescent Current vs. Supply Voltage (OFF) © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0 OUT OUT t don ...

Page 7

... T , Junction Temperature ( J Figure 19. Turn-On Delay vs. Junction Temperature Figure 21. Turn-Off Delay vs. Junction Temperature © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 Figure 18. On Resistance vs. Junction Temperature V = 12V IN R = 500 = 2µ 100 125 ...

Page 8

... Persists (SOA Protection Followed by Current-Limited Operation) Figure 26. OUT Shorted to GND, Short Condition Removed (SOA Protection Followed by Normal Operation) © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 . LIM Figure 23. Normal Startup to 0.5X I Figure 25. OUT Overloaded with 1.5X I Figure 27. OUT Overloaded with 1.5X I ...

Page 9

... Typical Operation Characteristics of FPF2702 Figure 28. OUT Shorted to GND, Short Condition Persists (SOA Protection Current Limit Followed by Current Limit) Figure 29. OUT Overloaded with 1.5X I © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 (Long-Duration Overload) LIM 9 www.fairchildsemi.com ...

Page 10

... OC NMOS the gate drive of the NMOS. OC © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 =500, C =2µF) Figure 31. 12V Turn-Off Delay (R L OUT ...

Page 11

... If the over-current condition persists beyond the blanking time, the FPF2700 latches off and shuts the switch off (Figure 32). If the ON pin is kept active, an auto-restart feature releases the switch and turns the switch on again after the auto-restart time (Figure 33). If the over-current condition persists beyond the blanking time, the FPF2701 latch-off feature shuts the switch off ...

Page 12

... The under-voltage lockout IN threshold has a 0.1V hysteresis. Figure 37. Under-Voltage Lockout Performance © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 Power Good (1) FPF270X has a power good feature. The PGOOD pin is an open-drain MOSFET that asserts HIGH when the output voltage reaches 90% of the input voltage (Figure 26) ...

Page 13

... In applications where FPF2702 can be exposed to persistent short-circuit conditions, it should be used only with external fault management control to protect the switch. © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0 possible to estimate the SOA for the two FPF2702 packages, MPX and MX, through their respective SOA curves shown in Figure 39 and Figure 40 ...

Page 14

... During startup, the total output current consists of both the load current and the charge current of the output capacitor. For the FPF2700 and FPF2701; if the total output current exceeds the set current limit threshold (determined via R ) for longer than the blanking time, SET the device may not be able to start properly ...

Page 15

... DAP. Figure 41. Two Through-Hole Open Vias Embedded in the DAP © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 3. The IN, OUT, and GND pins dissipate most of the heat generated during high-load current condition. The layout suggested in Figure 42 and Figure 43 is strongly recommended illustrating a proper layout for devices in MLP 3x3 packages ...

Page 16

... Thermal performance of the board is improved using the techniques recommended in the © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 layout recommendations section. Additional information about demonstration board can be found in the FPF270X board users guide. ...

Page 17

... Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 5.00 4.80 A 3.81 ...

Page 18

... Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2010 Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 3. 3.00 ...

Page 19

... Fairchild Semiconductor Corporation FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2 19 www.fairchildsemi.com ...

Related keywords