P89LV51RD2BBC,557 NXP Semiconductors, P89LV51RD2BBC,557 Datasheet - Page 55

• Manufacturer Part Number: P89LV51RD2BBC,557
• Description: IC 80C51 MCU FLASH 64K 44-TQFP
• Manufacturer: NXP Semiconductors
• Series: 89LVr

Specifications of P89LV51RD2BBC,557

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 33MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Processor Series: P89LV5x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: 0 C
• Cpu Family: 89LV
• Device Core: 80C51
• Device Core Size: 8b
• Frequency (max): 40MHz
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1017 - BOARD 44-ZIF PLCC SOCKET622-1008 - BOARD FOR LPC9103 10-HVSON622-1001 - USB IN-CIRCUIT PROG 80C51ISP
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-1289; 935274177557; P89LV51RD2BBC

NXP Semiconductors
Table 43.
P89LV51RB2_RC2_RD2_5
Product data sheet
Description
External
interrupt 0
Brownout
T0
External
interrupt 1
T1
PCA
UART/SPI
T2
Interrupt polling sequence
6.10 Security bit
6.11 Interrupt priority and polling sequence
Interrupt flag
IE0
-
TF0
IE1
TF1
CF/CCFn
TI/RI/SPIF
TF2, EXF2
The Security Bit protects against software piracy and prevents the contents of the flash
from being read by unauthorized parties in Parallel Programmer mode. It also protects
against code corruption resulting from accidental erasing and programming to the internal
flash memory.
When the Security Bit is activated, all parallel programming commands except for
Chip-Erase are ignored (thus the device cannot be read). However, ISP reading, writing,
or erasing of the user’s code can still be performed if the serial number and length has not
been programmed. Therefore, when a user requests to program the Security Bit, the
programmer should prompt the user and program a serial number into the device.
The device supports eight interrupt sources under a four level priority scheme.
summarizes the polling sequence of the supported interrupts. Note that the SPI serial
interface and the UART share the same interrupt vector. (See
Vector address Interrupt
0003H
004BH
000BH
0013H
001BH
0033H
0023H
002BH
Rev. 05 — 15 December 2009
enable bit
EX0
EBO
ET0
EX1
ET1
EC
ES
ET2
P89LV51RB2/RC2/RD2
Interrupt
priority bit
PX0/H
PBO/H
PT0/H
PX1/H
PT1/H
PPCH
PS/H
PT2/H
8-bit microcontrollers with 80C51 core
Service
priority
1 (highest)
2
3
4
5
6
7
8
Figure
26).
© NXP B.V. 2009. All rights reserved.
Wake-up
power-down
yes
no
no
yes
no
no
no
no
Table 43
55 of 76