MC9S08JM60CGT Freescale Semiconductor, MC9S08JM60CGT Datasheet - Page 210

• Manufacturer Part Number: MC9S08JM60CGT
• Description: IC MCU 8BIT 60K FLASH 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08JM60CGT

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 37
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN
• Processor Series: S08JM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOJM, DEMOJMSKT, DEMOFLEXISJMSD, DEMO9S08JM16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 24MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: QFN EP
• Package: 48QFN EP
• Family Name: HCS08
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: DEMOJM - KIT DEMO FOR JM MCU FAMILYDEMOJMSKT - BOARD DEMO S08JM CARD W/SOCKET
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Multi-Purpose Clock Generator (S08MCGV1)
12.5.3
Calibrating the Internal Reference Clock (IRC)
The IRC is calibrated by writing to the MCGTRM register first, then using the FTRIM bit to “fine tune”
the frequency. We will refer to this total 9-bit value as the trim value, ranging from 0x000 to 0x1FF, where
the FTRIM bit is the LSB.
The trim value after a POR is always 0x100 (MCGTRM = 0x80 and FTRIM = 0). Writing a larger value
will decrease the frequency and smaller values will increase the frequency. The trim value is linear with
the period, except that slight variations in wafer fab processing produce slight non-linearities between trim
value and period. These non-linearities are why an iterative trimming approach to search for the best trim
value is recommended. In example #4 later in this section, this approach will be demonstrated.
After a trim value has been found for a device, this value can be stored in FLASH memory to save the
value. If power is removed from the device, the IRC can easily be re-trimmed by copying the saved value
from FLASH to the MCG registers. Freescale identifies recommended FLASH locations for storing the
trim value for each MCU. Consult the memory map in the data sheet for these locations. On devices that
are factory trimmed, the factory trim value will be stored in these locations.
12.5.3.1
Example #5: Internal Reference Clock Trim
For applications that require a tight frequency tolerance, a trimming procedure is provided that will allow
a very accurate internal clock source. This section outlines one example of trimming the internal oscillator.
Many other possible trimming procedures are valid and can be used.
In the example below, the MCG trim will be calibrated for the 9-bit MCGTRM and FTRIM collective
value. This value will be referred to as TRMVAL.
MC9S08JM60 Series Data Sheet, Rev. 3
210
Freescale Semiconductor