PIC18F26K20-E/ML Microchip Technology, PIC18F26K20-E/ML Datasheet - Page 236

• Manufacturer Part Number: PIC18F26K20-E/ML
• Description: IC PIC MCU FLASH 32KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K20-E/ML

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.84375KB
• Cpu Speed: 64MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP, ECCP, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / Rohs Status: Details

PIC18F2XK20/4XK20
FIGURE 18-2:
The operation of the EUSART module is controlled
through three registers:
• Transmit Status and Control (TXSTA)
• Receive Status and Control (RCSTA)
• Baud Rate Control (BAUDCON)
These
Register 18-2 and Register 18-3, respectively.
For all modes of EUSART operation, the TRIS control
bits corresponding to the RX/DT and TX/CK pins should
be set to ‘1’. The EUSART control will automatically
reconfigure the pin from input to output, as needed.
When the receiver or transmiter section is not enabled
then the corresponding RX or TX pin may be used for
general purpose input and output.
DS41303E-page 234
BRG16
Baud Rate Generator
SPBRGH
registers
SPBRG
RX/DT pin
are
+ 1
EUSART RECEIVE BLOCK DIAGRAM
detailed
Multiplier
BRG16
SYNC
BRGH
Pin Buffer
and Control
in
1 X 0 0
X 1 1 0
X 1 0 1
x4
Register 18-1,
x16 x64
F
OSC
0
0
0
Preliminary
n
Data
Recovery
÷ n
FERR
Stop
MSb
CREN
(8)
RX9D
7
RX9
RSR Register
© 2009 Microchip Technology Inc.
RCREG Register
• • •
OERR
8
1
RCIF
RCIE
Data Bus
0
START
LSb
RCIDL
Interrupt
FIFO