ATMEGA8L-8PU Atmel, ATMEGA8L-8PU Datasheet - Page 105

• Manufacturer Part Number: ATMEGA8L-8PU
• Description: IC AVR MCU 8K 8MHZ 3V 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8L-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SPI/TWI/USART
• Total Internal Ram Size: 1KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Output Compare
Unit
2486Z–AVR–02/11
The 8-bit comparator continuously compares TCNT2 with the Output Compare Register
(OCR2). Whenever TCNT2 equals OCR2, the comparator signals a match. A match will set the
Output Compare Flag (OCF2) at the next timer clock cycle. If enabled (OCIE2 = 1), the Output
Compare Flag generates an Output Compare interrupt. The OCF2 Flag is automatically cleared
when the interrupt is executed. Alternatively, the OCF2 Flag can be cleared by software by writ-
ing a logical one to its I/O bit location. The waveform generator uses the match signal to
generate an output according to operating mode set by the WGM21:0 bits and Compare Output
mode (COM21:0) bits. The max and bottom signals are used by the waveform generator for han-
dling the special cases of the extreme values in some modes of operation (see
Operation” on page
Figure 47
Figure 47. Output Compare Unit, Block Diagram
The OCR2 Register is double buffered when using any of the Pulse Width Modulation (PWM)
modes. For the normal and Clear Timer on Compare (CTC) modes of operation, the double buff-
ering is disabled. The double buffering synchronizes the update of the OCR2 Compare Register
to either top or bottom of the counting sequence. The synchronization prevents the occurrence
of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free.
The OCR2 Register access may seem complex, but this is not case. When the double buffering
is enabled, the CPU has access to the OCR2 Buffer Register, and if double buffering is disabled
the CPU will access the OCR2 directly.
shows a block diagram of the Output Compare unit.
BOTTOM
FOCn
TOP
108).
OCRn
Waveform Generator
WGMn1:0
=
(8-bit Comparator )
DATA BUS
COMn1:0
TCNTn
OCFn (Int. Req.)
ATmega8(L)
OCxy
“Modes of
105