AT91SAM9260B-QU Atmel, AT91SAM9260B-QU Datasheet - Page 293

• Manufacturer Part Number: AT91SAM9260B-QU
• Description: IC ARM9 MCU 208-PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9260B-QU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Package: 208PQFP
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 180 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 96
• Interface Type: EBI/Ethernet/SPI/TWI/UART/USART/USB
• On-chip Adc: 4-chx10-bit
• Number Of Timers: 6
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Ram Size: 8 KB
• Maximum Clock Frequency: 180 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9260-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT91
• Device Core Size: 32b
• Frequency (max): 180MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 96
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: PQFP
• For Use With: AT91SAM9260-EK - KIT EVAL FOR AT91SAM9260AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

26.8.4.5
6221I–ATARM–17-Jul-09
Fast Forcing
Note:
Another way to handle the fast interrupt is to map the interrupt service routine at the address of
the ARM vector 0x1C. This method does not use the vectoring, so that reading AIC_FVR must
be performed at the very beginning of the handler operation. However, this method saves the
execution of a branch instruction.
The Fast Forcing feature of the advanced interrupt controller provides redirection of any normal
Interrupt source on the fast interrupt controller.
Fast Forcing is enabled or disabled by writing to the Fast Forcing Enable Register (AIC_FFER)
and the Fast Forcing Disable Register (AIC_FFDR). Writing to these registers results in an
update of the Fast Forcing Status Register (AIC_FFSR) that controls the feature for each inter-
nal or external interrupt source.
When Fast Forcing is disabled, the interrupt sources are handled as described in the previous
pages.
When Fast Forcing is enabled, the edge/level programming and, in certain cases, edge detec-
tion of the interrupt source is still active but the source cannot trigger a normal interrupt to the
processor and is not seen by the priority handler.
If the interrupt source is programmed in level-sensitive mode and an active level is sampled,
Fast Forcing results in the assertion of the nFIQ line to the core.
If the interrupt source is programmed in edge-triggered mode and an active edge is detected,
Fast Forcing results in the assertion of the nFIQ line to the core.
1. The CPSR is stored in SPSR_fiq, the current value of the program counter is loaded in
2. The ARM core enters FIQ mode.
3. When the instruction loaded at address 0x1C is executed, the program counter is
4. The previous step enables branching to the corresponding interrupt service routine. It is
5. The Interrupt Handler can then proceed as required. It is not necessary to save regis-
6. Finally, the Link Register R14_fiq is restored into the PC after decrementing it by four
the FIQ link register (R14_FIQ) and the program counter (R15) is loaded with 0x1C. In
the following cycle, during fetch at address 0x20, the ARM core adjusts R14_fiq, decre-
menting it by four.
loaded with the value read in AIC_FVR. Reading the AIC_FVR has effect of automati-
cally clearing the fast interrupt, if it has been programmed to be edge triggered. In this
case only, it de-asserts the nFIQ line on the processor.
not necessary to save the link register R14_fiq and SPSR_fiq if nested fast interrupts
are not needed.
ters R8 to R13 because FIQ mode has its own dedicated registers and the user R8 to
R13 are banked. The other registers, R0 to R7, must be saved before being used, and
restored at the end (before the next step). Note that if the fast interrupt is programmed
to be level sensitive, the source of the interrupt must be cleared during this phase in
order to de-assert the interrupt source 0.
(with instruction SUB PC, LR, #4 for example). This has the effect of returning from
the interrupt to whatever was being executed before, loading the CPSR with the SPSR
and masking or unmasking the fast interrupt depending on the state saved in the
SPSR.
The “F” bit in SPSR is significant. If it is set, it indicates that the ARM core was just about to mask
FIQ interrupts when the mask instruction was interrupted. Hence when the SPSR is restored, the
interrupted instruction is completed (FIQ is masked).
AT91SAM9260
293