AT91SAM9260B-QU Atmel, AT91SAM9260B-QU Datasheet - Page 765

• Manufacturer Part Number: AT91SAM9260B-QU
• Description: IC ARM9 MCU 208-PQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9260B-QU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: POR, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-MQFP, 208-PQFP
• Package: 208PQFP
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 180 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 96
• Interface Type: EBI/Ethernet/SPI/TWI/UART/USART/USB
• On-chip Adc: 4-chx10-bit
• Number Of Timers: 6
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Ram Size: 8 KB
• Maximum Clock Frequency: 180 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9260-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT91
• Device Core Size: 32b
• Frequency (max): 180MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 96
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: PQFP
• For Use With: AT91SAM9260-EK - KIT EVAL FOR AT91SAM9260AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

43.2.13
43.2.13.1
43.2.14
43.2.14.1
43.2.15
43.2.15.1
43.2.16
43.2.16.1
6221I–ATARM–17-Jul-09
Shutdown Controller (SHDWC)
System Controller
Two-wire Interface (TWI)
UHP
SHDWC: SHDN Signal may be Driven to Low Level Voltage During Device Power-on
Possible Event Loss when Reading RTT_SR
Switch from Slave to Master Mode
Non-ISO IN Transfers
If only VDDBU is powered during boot sequence (No VDDCORE), the SHDN signal may be
driven to low level voltage after a delay.This delay is linked to the startup time of the slow clock
selected by OSCSEL signal.
If SHDN pin is connected to the Enable pin (EN) of the VDDCORE regulator, VDDCORE estab-
lishment does not occur and the system does not start.
If an event (RTTINC or ALMS) occurs within the same slow clock cycle as when the RTT_SR is
read, the corresponding bit might be cleared. This can lead to the loss of this event.
The software must handle an RTT event as an interrupt and should not poll RTT_SR.
At the end of transfer in slave mode, the slave mode is disabled, the master mode is enabled
and thus a transfer in master mode can be performed. In the current device, the start event is
correctly generated but the SCL line is stuck at 1, so no transfer is possible.
Two workarounds are possible:
or
Conditions:
Consider the following sequence:
1. VDDCORE must be established within the delay corresponding to the startup time of
2. Add a glue logic to latch the rising edge of the SHDN signal. The reset of the latch out-
1. Perform a software reset before going to master mode (TWI must be reconfigured).
2. Perform a slave read access before switching to master mode.
1. The Host controller issues an IN token.
2. The Device provides the IN data in a short packet.
3. The Host controller writes the received data to the system memory.
4. The Host controller is now supposed to carry out two Write transactions (TD status
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
the slow clock selected by OSCSEL.
put (EN_REG) can be connected to a PIO and used to enter the shutdown mode.
write and TD retirement write) to the system memory in order to complete the status
update.
AT91SAM9260
765