ATMEGA2560V-8AU Atmel, ATMEGA2560V-8AU Datasheet - Page 233

• Manufacturer Part Number: ATMEGA2560V-8AU
• Description: IC AVR MCU 256K 8MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA2560V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• A/d Inputs: 16-Channel, 10-Bit
• Cpu Speed: 8 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 86
• Interface: 2-Wire/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 100-pin TQFP
• Programmable Memory: 256K Bytes
• Timers: 2-8-bit, 4-16-bit
• Voltage, Range: 1.8-5.5 V
• Package: 100TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.2.1
22.3
2549M–AVR–09/10
SPI Data Modes and Timing
Clock Generation
A comparison of the USART in MSPIM mode and the SPI pins is shown in
240.
The Clock Generation logic generates the base clock for the Transmitter and Receiver. For
USART MSPIM mode of operation only internal clock generation (that is, master operation) is
supported. The Data Direction Register for the XCKn pin (DDR_XCKn) must therefore be set to
one (that is, as output) for the USART in MSPIM to operate correctly. Preferably the DDR_XCKn
should be set up before the USART in MSPIM is enabled (that is, TXENn and RXENn bit set to
one).
The internal clock generation used in MSPIM mode is identical to the USART synchronous mas-
ter mode. The baud rate or UBRRn setting can therefore be calculated using the same
equations, see
Table 22-1.
Note:
There are four combinations of XCKn (SCK) phase and polarity with respect to serial data, which
are determined by control bits UCPHAn and UCPOLn. The data transfer timing diagrams are
shown in
the XCKn signal, ensuring sufficient time for data signals to stabilize. The UCPOLn and
UCPHAn functionality is summarized in
these bits will corrupt all ongoing communication for both the Receiver and Transmitter.
Table 22-2.
Operating Mode
Synchronous Master
mode
UCPOLn
BAUD
f
UBRRn
OSC
0
0
1
1
1. The baud rate is defined to be the transfer rate in bit per second (bps).
Figure 22-1 on page
Equations for Calculating Baud Rate Register Setting
UCPOLn and UCPHAn Functionality-
Table
UCPHAn
22-1.
Baud rate (in bits per second, bps).
System Oscillator clock frequency.
Contents of the UBRRnH and UBRRnL Registers, (0-4095).
0
1
0
1
Equation for Calculating Baud
BAUD
234. Data bits are shifted out and latched in on opposite edges of
ATmega640/1280/1281/2560/2561
=
SPI Mode
Rate
-------------------------------------- -
2 UBRRn
(
0
1
2
3
(1)
f
OSC
Table
+
22-2. Note that changing the setting of any of
1
)
Sample (Rising)
Sample (Falling)
Leading Edge
Setup (Rising)
Setup (Falling)
Equation for Calculating
UBRRn
UBRRn Value
=
------------------- - 1
2BAUD
f
OSC
Table 22-4 on page
Sample (Falling)
Sample (Rising)
Setup (Falling)
Setup (Rising)
Trailing Edge
–
233