ATMEGA2560V-8AU Atmel, ATMEGA2560V-8AU Datasheet - Page 252

• Manufacturer Part Number: ATMEGA2560V-8AU
• Description: IC AVR MCU 256K 8MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA2560V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• A/d Inputs: 16-Channel, 10-Bit
• Cpu Speed: 8 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 86
• Interface: 2-Wire/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 100-pin TQFP
• Programmable Memory: 256K Bytes
• Timers: 2-8-bit, 4-16-bit
• Voltage, Range: 1.8-5.5 V
• Package: 100TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

23.7
2549M–AVR–09/10
6
7
wait3:
in
sbrs r16,TWINT
rjmp wait3
in
andi r16, 0xF8
cpi
brne ERROR
ldi
out
Transmission Modes
Assembly Code Example
r16,TWCR
r16,TWSR
r16, MT_DATA_ACK
r16, (1<<TWINT)|(1<<TWEN)|
(1<<TWSTO)
TWCR, r16
The TWI can operate in one of four major modes. These are named Master Transmitter (MT),
Master Receiver (MR), Slave Transmitter (ST) and Slave Receiver (SR). Several of these
modes can be used in the same application. As an example, the TWI can use MT mode to write
data into a TWI EEPROM, MR mode to read the data back from the EEPROM. If other masters
are present in the system, some of these might transmit data to the TWI, and then SR mode
would be used. It is the application software that decides which modes are legal.
The following sections describe each of these modes. Possible status codes are described
along with figures detailing data transmission in each of the modes. These figures contain the
following abbreviations:
S:
Rs:
R:
W:
A:
A:
Data: 8-bit data byte
P:
SLA: Slave Address
In
TWINT Flag is set. The numbers in the circles show the status code held in TWSR, with the
prescaler bits masked to zero. At these points, actions must be taken by the application to con-
tinue or complete the TWI transfer. The TWI transfer is suspended until the TWINT Flag is
cleared by software.
When the TWINT Flag is set, the status code in TWSR is used to determine the appropriate soft-
ware action. For each status code, the required software action and details of the following serial
transfer are given in
bits are masked to zero in these tables.
Figure 23-12 on page 255
START condition
REPEATED START condition
Read bit (high level at SDA)
Write bit (low level at SDA)
Acknowledge bit (low level at SDA)
Not acknowledge bit (high level at SDA)
STOP condition
Table 23-2 on page 254
while (!(TWCR & (1<<TWINT)))
if ((TWSR & 0xF8) !=
MT_DATA_ACK)
TWCR = (1<<TWINT)|(1<<TWEN)|
(1<<TWSTO);
to
;
ERROR();
ATmega640/1280/1281/2560/2561
Figure 23-18 on page
C Example
to
Table 23-5 on page
264, circles are used to indicate that the
indicates that the DATA has been
transmitted, and ACK/NACK has
Register. Mask prescaler bits. If
MT_DATA_ACK go to ERROR
Wait for TWINT Flag set. This
Check value of TWI Status
263. Note that the prescaler
Transmit STOP condition
status different from
been received.
Comments
252