ST72F63BH6T1 STMicroelectronics, ST72F63BH6T1 Datasheet - Page 80

• Manufacturer Part Number: ST72F63BH6T1
• Description: IC MCU 8BIT 32K FLASH 48-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F63BH6T1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 48-LQFP
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 1
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MDTU3-EPB/US, ST72F63B-SK/RAIS, ST7MDTU3-EMU3, STX-RLINK
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit, 8 Channel / 8 bit, 12 Channel
• For Use With: 497-5521 - EVAL BOARD LOW SPEED USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

On-chip peripherals
11.3
11.3.1
11.3.2
11.3.3
80/186
Serial communications interface (SCI)
Introduction
The Serial Communications Interface (SCI) offers a flexible means of full-duplex data
exchange with external equipment requiring an industry standard NRZ asynchronous serial
data format. The SCI offers a very wide range of baud rates using two baud rate generator
systems.
Main features
●
●
●
●
●
●
●
●
●
●
●
●
General description
The interface is externally connected to another device by two pins (see
●
●
– Address bit (MSB)
– Idle line
– Overrun error
– Noise error
– Frame error
– Parity error
– Transmit data register empty
– Transmission complete
– Receive data register full
– Idle line received
– Overrun error detected
– Parity error
– Transmits parity bit
– Checks parity of received data byte
Full duplex, asynchronous communications
NRZ standard format (Mark/Space)
Independently programmable transmit and receive baud rates up to 250K baud.
Programmable data word length (8 or 9 bits)
Receive buffer full, Transmit buffer empty and End of Transmission flags
Two receiver Wakeup modes:
Muting function for multiprocessor configurations
Separate enable bits for Transmitter and Receiver
Four error detection flags:
Six interrupt sources with flags:
Parity control:
Reduced power consumption mode
TDO: Transmit Data output. When the transmitter and the receiver are disabled, the
output pin returns to its I/O port configuration. When the transmitter and/or the receiver
are enabled and nothing is to be transmitted, the TDO pin is at high level.
RDI: Receive Data input is the serial data input. Oversampling techniques are used for
data recovery by discriminating between valid incoming data and noise.
Doc ID 7516 Rev 8
Figure
42):
ST7263Bxx