F272-BAG-T-TR STMicroelectronics, F272-BAG-T-TR Datasheet - Page 99

• Manufacturer Part Number: F272-BAG-T-TR
• Description: MCU 16BIT 256K FLASH 144-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of F272-BAG-T-TR

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: ASC, CAN, EBI/EMI, I²C, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-TQFP, 144-VQFP
• Processor Series: ST10F27x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: ASC, CAN, I2C, SSC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

ST10F272B/ST10F272E
20.7
Figure 29. SW / WDT bidirectional RESET (EA=0) followed by a HW RESET
Reset circuitry
Internal reset circuitry is described in
resistor of 50kΩ to 250kΩ (The minimum reset time must be calculated using the lowest
value).
It also provides a programmable (BDRSTEN bit of SYSCON register) pull-down to output
internal reset state signal (synchronous reset, watchdog timer reset or software reset).
This bidirectional reset function is useful in applications where external devices require a
reset signal but cannot be connected to RSTOUT pin.
This is the case of an external memory running codes before EINIT (end of initialization)
instruction is executed. RSTOUT pin is pulled high only when EINIT is executed.
The RPD pin provides an internal weak pull-down resistor which discharges external
capacitor at a typical rate of 200µA. If bit PWDCFG of SYSCON register is set, an internal
pull-up resistor is activated at the end of the reset sequence. This pull-up will charge any
capacitor connected on RPD pin.
The simplest way to reset the ST10F272 is to insert a capacitor C1 between RSTIN pin and
V
RPD pin and V
50kΩ to 250kΩ (the minimum reset time must be determined by the lowest value). Select C1
that produce a sufficient discharge time to permit the internal or external oscillator and / or
internal PLL and the on-chip voltage regulator to stabilize.
SS
, and a capacitor between RPD pin and V
RSTIN
P0[7:2]
RSTOUT
RSTF
(After Filter)
P0[15:13]
P0[12:8]
P0[1:0]
ALE
RST
DD
. The input RSTIN provides an internal pull-up device equalling a resistor of
≤ 500 ns
≥ 50 ns
Figure
not transparent
not transparent
not transparent
1024 TCL
transparent
32. The RSTIN pin provides an internal pull-up
SS
(C0) with a pull-up resistor R0 between
At this time RSTF is sampled LOW
so HW Reset is entered
not t.
not t.
≤ 500 ns
8 TCL
≥ 50 ns
System reset
99/182