C8051F521A-IM Silicon Laboratories Inc, C8051F521A-IM Datasheet - Page 104

• Manufacturer Part Number: C8051F521A-IM
• Description: IC 8051 MCU 8K FLASH 10DFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F52xr

Specifications of C8051F521A-IM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 10-DFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 6
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1488 - KIT DEV C8051F53XA, C8051F52XA770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1455 - ADAPTER PROGRAM TOOLSTICK F520
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1490-5

C8051F52x/F52xA/F53x/F53xA
10.5. External Interrupts
The INT0 and INT0 external interrupt sources are configurable as active high or low, edge or level sensi-
tive. The IN0PL (INT0 Polarity) and IN1PL (INT0 Polarity) bits in the IT01CF register select active high or
active low; the IT0 and IT1 bits in TCON (Section “18.1. Timer 0 and Timer 1” on page 181) select level or
edge sensitive. The table below lists the possible configurations.
INT0 and INT0 are assigned to Port pins as defined in the IT01CF register (see SFR Definition 10.5). Note
that INT0 and INT0 Port pin assignments are independent of any Crossbar assignments. INT0 and INT0
will monitor their assigned Port pins without disturbing the peripheral that was assigned the Port pin via the
Crossbar. To assign a Port pin only to INT0 and/or INT0, configure the Crossbar to skip the selected pin(s).
This is accomplished by setting the associated bit in register XBR0 (see Section “13.1. Priority Crossbar
Decoder” on page 121 for complete details on configuring the Crossbar).
In the typical configuration, the external interrupt pins should be skipped in the crossbar and configured as
open-drain with the pin latch set to 1. See Section “13. Port Input/Output” on page 119 for more informa-
tion.
IE0 (TCON.1) and IE1 (TCON.3) serve as the interrupt-pending flags for the INT0 and INT0 external inter-
rupts, respectively. If an INT0 or INT0 external interrupt is configured as edge-sensitive, the corresponding
interrupt-pending flag is automatically cleared by the hardware when the CPU vectors to the ISR. When
configured as level sensitive, the interrupt-pending flag remains logic 1 while the input is active as defined
by the corresponding polarity bit (IN0PL or IN1PL); the flag remains logic 0 while the input is inactive. The
external interrupt source must hold the input active until the interrupt request is recognized. It must then
deactivate the interrupt request before execution of the ISR completes or another interrupt request will be
generated.
104
IT0
1
1
0
0
IN0PL
0
1
0
1
Active high, edge sensitive
Active high, level sensitive
Active low, edge sensitive
Active low, level sensitive
INT0 Interrupt
Rev. 1.3
IT1
1
1
0
0
IN1PL
0
1
0
1
Active high, edge sensitive
Active high, level sensitive
Active low, edge sensitive
Active low, level sensitive
INT1 Interrupt