TMP86FH46ANG(Z) Toshiba, TMP86FH46ANG(Z) Datasheet - Page 57

IC MCU 8BIT FLASH 16KB 42-SDIP

TMP86FH46ANG(Z)

Manufacturer Part Number
TMP86FH46ANG(Z)
Description
IC MCU 8BIT FLASH 16KB 42-SDIP
Manufacturer
Toshiba
Series
TLCS-870/Cr
Datasheet

Specifications of TMP86FH46ANG(Z)

Core Processor
870/C
Core Size
8-Bit
Speed
16MHz
Connectivity
SIO, UART/USART
Peripherals
LED, PWM, WDT
Number Of I /o
33
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
42-SDIP (0.600", 15.24mm)
Processor Series
TLCS-870
Core
870/C
Data Bus Width
8 bit
Data Ram Size
512 B
Interface Type
SIO, UART
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
33
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Development Tools By Supplier
BMSKTOPAS86FH47(AND), BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
For Use With
BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP86C909XB - EMULATION CHIP FOR TMP86F SDIP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
Other names
TMP86FH46ANGZ
External Interrupt Control Register
EINTCR
(0037H)
Note 1: fc: High-frequency clock [Hz], *: Don’t care
Note 2: When the system clock frequency is switched between high and low or when the external interrupt control register
Note 3: The maximum time from modifying INT1NC until a noise reject time is changed is 2
Note 4: In case
(EINTCR) is overwritten, the noise canceller may not operate normally. It is recommended that external interrupts are dis-
abled using the interrupt enable register (EIR).
even if the INT4 edge select is specified as "H" level. The rising edge is needed after
INT1NC
7
INT1NC
INT0EN
INT4 ES
INT3 ES
INT2 ES
INT1 ES
RESET
INT0EN
6
pin is released while the state of INT4 pin keeps "H" level, the external interrupt 4 request is not generated
Noise reject time select
P00/
INT4 edge select
INT3 edge select
INT2 edge select
INT1 edge select
5
INT0
INT4ES
pin configuration
4
INT3ES
3
Page 43
0: Pulses of less than 63/fc [s] are eliminated as noise
1: Pulses of less than 15/fc [s] are eliminated as noise
0: P00 input/output port
1:
00: Rising edge
01: Falling edge
10: Rising edge and Falling edge
11: H level
0: Rising edge
1: Falling edge
0: Rising edge
1: Falling edge
0: Rising edge
1: Falling edge
INT0
INT2ES
2
pin (Port P00 should be set to an input mode)
INT1ES
1
0
6
/fc.
(Initial value: 0000 000*)
RESET
pin is released.
TMP86FH46ANG
R/W
R/W
R/W
R/W
R/W
R/W

Related parts for TMP86FH46ANG(Z)