C8051F023R Silicon Laboratories Inc, C8051F023R Datasheet - Page 268

IC 8051 MCU 64K FLASH 64TQFP

C8051F023R

Manufacturer Part Number
C8051F023R
Description
IC 8051 MCU 64K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Datasheets

Specifications of C8051F023R

Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x10b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Other names
336-1035-2

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
C8051F023R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F020/1/2/3
24.2. Flash Programming Commands
The Flash memory can be programmed directly over the JTAG interface using the Flash Control, Flash Data, Flash
Address, and Flash Scale registers. These Indirect Data Registers are accessed via the JTAG Instruction Register.
Read and write operations on indirect data registers are performed by first setting the appropriate DR address in the
IR register. Each read or write is then initiated by writing the appropriate Indirect Operation Code (IndOpCode) to the
selected data register. Incoming commands to this register have the following format:
IndOpCode: These bit set the operation to perform according to the following table:
The Poll operation is used to check the Busy bit as described below. Although a Capture-DR is performed, no
Update-DR is allowed for the Poll operation. Since updates are disabled, polling can be accomplished by shifting in/
out a single bit.
The Read operation initiates a read from the register addressed by the DRAddress. Reads can be initiated by shifting
only 2 bits into the indirect register. After the read operation is initiated, polling of the Busy bit must be performed to
determine when the operation is complete.
The write operation initiates a write of WriteData to the register addressed by DRAddress. Registers of any width up
to 18 bits can be written. If the register to be written contains fewer than 18 bits, the data in WriteData should be left-
justified, i.e. its MSB should occupy bit 17 above. This allows shorter registers to be written in fewer JTAG clock
cycles. For example, an 8-bit register could be written by shifting only 10 bits. After a Write is initiated, the Busy bit
should be polled to determine when the next operation can be initiated. The contents of the Instruction Register
should not be altered while either a read or write operation is busy.
Outgoing data from the indirect Data Register has the following format:
The Busy bit indicates that the current operation is not complete. It goes high when an operation is initiated and
returns low when complete. Read and Write commands are ignored while Busy is high. In fact, if polling for Busy to
be low will be followed by another read or write operation, JTAG writes of the next operation can be made while
checking for Busy to be low. They will be ignored until Busy is read low, at which time the new operation will initi-
ate. This bit is placed ate bit 0 to allow polling by single-bit shifts. When waiting for a Read to complete and Busy is
0, the following 18 bits can be shifted out to obtain the resulting data. ReadData is always right-justified. This allows
registers shorter than 18 bits to be read using a reduced number of shifts. For example, the results from a byte-read
requires 9 bit shifts (Busy + 8 bits).
268
19
0
IndOpCode
19:18
IndOpCode
0x
10
11
ReadData
Rev. 1.4
18:1
Operation
WriteData
Write
Read
Poll
17:0
Busy
0

Related parts for C8051F023R