C8051F023R Silicon Laboratories Inc, C8051F023R Datasheet - Page 44

IC 8051 MCU 64K FLASH 64TQFP

C8051F023R

Manufacturer Part Number
C8051F023R
Description
IC 8051 MCU 64K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Datasheets

Specifications of C8051F023R

Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x10b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Other names
336-1035-2

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
C8051F023R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F020/1
The Temperature Sensor transfer function is shown in Figure 5.2. The output voltage (V
the Temperature Sensor is selected by bits AMX0AD3-0 in register AMX0SL; this voltage will be amplified by the
PGA according to the user-programmed PGA settings.
5.2.
ADC0 has a maximum conversion speed of 100 ksps. The ADC0 conversion clock is derived from the system clock
divided by the value held in the ADCSC bits of register ADC0CF.
5.2.1. Starting a Conversion
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC0 Start of Conver-
sion Mode bits (AD0CM1, AD0CM0) in ADC0CN. Conversions may be initiated by:
The AD0BUSY bit is set to logic 1 during conversion and restored to logic 0 when conversion is complete. The fall-
ing edge of AD0BUSY triggers an interrupt (when enabled) and sets the AD0INT interrupt flag (ADC0CN.5). Con-
verted data is available in the ADC0 data word MSB and LSB registers, ADC0H, ADC0L. Converted data can be
either left or right justified in the ADC0H:ADC0L register pair (see example in Figure 5.11) depending on the pro-
grammed state of the AD0LJST bit in the ADC0CN register.
When initiating conversions by writing a ‘1’ to AD0BUSY, the AD0INT bit should be polled to determine when a
conversion has completed (ADC0 interrupts may also be used). The recommended polling procedure is shown below.
44
ADC Modes of Operation
1.
2.
3.
4.
Step 1. Write a ‘0’ to AD0INT;
Step 2. Write a ‘1’ to AD0BUSY;
Step 3. Poll AD0INT for ‘1’;
Step 4. Process ADC0 data.
Writing a ‘1’ to the AD0BUSY bit of ADC0CN;
A Timer 3 overflow (i.e. timed continuous conversions);
A rising edge detected on the external ADC convert start signal, CNVSTR;
A Timer 2 overflow (i.e. timed continuous conversions).
1.000
0.900
0.800
0.700
0.600
0.500
(Volts)
Figure 5.2. Temperature Sensor Transfer Function
-50
0
Rev. 1.4
V
TEMP
50
= 0.00286(TEMP
for PGA Gain = 1
100
C
) + 0.776
TEMP
(Celsius)
) is the PGA input when

Related parts for C8051F023R