DSPIC30F2010-30I/SO Microchip Technology, DSPIC30F2010-30I/SO Datasheet - Page 15

• Manufacturer Part Number: DSPIC30F2010-30I/SO
• Description: IC DSPIC MCU/DSP 12K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

TABLE 5-7:
© 2010 Microchip Technology Inc.
SSS<2:0>
SWRP
GSS<1:0>
GCP
GWRP
BKBUG
COE
ICS<1:0>
RESERVED
Bit Field
—
FSS
FSS
FGS
FGS
FGS
FICD
FICD
FICD
FBS, FSS, FGS Reserved (read as ‘1’, write as ‘1’)
All
CONFIGURATION BITS DESCRIPTION (CONTINUED)
Register
Secure Segment Program Memory Code Protection (only present in
dsPIC30F5011/5013/6010A/6011A/6012A/6013A/6014A/6015)
111 = No Secure Segment
110 = Standard security; Small-sized Secure Program Flash
101 = Standard security; Medium-sized Secure Program Flash
100 = Standard security; Large-sized Secure Program Flash
011 = No Secure Segment
010 = High security; Small-sized Secure Program Flash
001 = High security; Medium-sized Secure Program Flash
000 = High security; Large-sized Secure Program Flash
Secure Segment Program Memory Write Protection (only present in
dsPIC30F5011/5013/6010A/6011A/6012A/6013A/6014A/6015)
1 = Secure Segment program memory is not write-protected
0 = Secure program memory is write-protected
General Segment Program Memory Code Protection (only present in
dsPIC30F5011/5013/6010A/6011A/6012A/6013A/6014A/6015)
11 = Code protection is disabled
10 = Standard security code protection is enabled
0x = High security code protection is enabled
General Segment Program Memory Code Protection (present in all devices
except dsPIC30F5011/5013/6010A/6011A/6012A/6013A/6014A/6015)
1 = General Segment program memory is not code-protected
0 = General Segment program memory is code-protected
General Segment Program Memory Write Protection
1 = General Segment program memory is not write-protected
0 = General Segment program memory is write-protected
Debugger/Emulator Enable
1 = Device will reset into Operational mode
0 = Device will reset into Debug/Emulation mode
Debugger/Emulator Enable
1 = Device will reset into Operational mode
0 = Device will reset into Clip-on Emulation mode
ICD Communication Channel Select
11 = Communicate on PGC/EMUC and PGD/EMUD
10 = Communicate on EMUC1 and EMUD1
01 = Communicate on EMUC2 and EMUD2
00 = Communicate on EMUC3 and EMUD3
Unimplemented (read as ‘0’, write as ‘0’)
[Secure Segment starts after BS and ends at 0x001FFF]
[Secure Segment starts after BS and ends at 0x003FFF]
[Secure Segment starts after BS and ends at 0x007FFF]
[Secure Segment starts after BS and ends at 0x001FFF]
[Secure Segment starts after BS and ends at 0x003FFF]
[Secure Segment starts after BS and ends at 0x007FFF]
Description
DS70102K-page 15