DSPIC30F2010-30I/SO Microchip Technology, DSPIC30F2010-30I/SO Datasheet - Page 27

• Manufacturer Part Number: DSPIC30F2010-30I/SO
• Description: IC DSPIC MCU/DSP 12K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

8.5.5
The PROGP command instructs the programming
executive to program one row of code memory
(32 instruction words) to the specified memory
address. Programming begins with the row address
specified in the command. The destination address
should be a multiple of 0x40.
The data to program to memory, located in command
words D_1 through D_48, must be arranged using the
packed instruction word format shown in
After all data has been programmed to code memory,
the programming executive verifies the programmed
data against the data in the command.
Expected Response (2 words):
0x1500
0x0002
© 2010 Microchip Technology Inc.
15
Opcode
Length
Reserved
Addr_MSB
Addr_LS
D_1
D_2
...
D_48
Note:
Opcode
Field
Reserved
12 11
PROGP COMMAND
Refer to
information.
0x5
0x33
0x0
MSB of 24-bit destination address
LS 16 bits of 24-bit destination address
16-bit data word 1
16-bit data word 2
16-bit data word 3 through 47
16-bit data word 48
Table 5-2
Addr_LS
D_N
D_1
D_2
...
8 7
Description
for code memory size
Length
Addr_MSB
Figure
8-2.
0
8.5.6
The PROGC command programs data to the specified
Configuration register and verifies the programming.
Configuration registers are 16 bits wide, and this
command allows one Configuration register to be
programmed.
Expected Response (2 words):
0x1600
0x0002
15
Opcode
Length
Reserved
Addr_MSB
Addr_LS
Data
Note:
Opcode
Field
Reserved
12 11
PROGC COMMAND
This command can only be used for
programming Configuration registers.
0x6
0x4
0x0
MSB of 24-bit destination address
LS 16 bits of 24-bit destination
address
Data to program
Addr_LS
Data
8 7
Description
Length
Addr_MSB
DS70102K-page 27
0