C8051F350 Silicon Laboratories Inc, C8051F350 Datasheet - Page 214

• Manufacturer Part Number: C8051F350
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F350

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x24b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Data Bus Width: 8 bit
• Data Rom Size: 128 B
• On-chip Adc: 10 bit
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Mounting Style: SMD/SMT
• Height: 1.4 mm
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Width: 7 mm
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

C8051F350/1/2/3
23.2.5. 8-Bit Pulse Width Modulator Mode
Each module can be used independently to generate a pulse width modulated (PWM) output on its associ-
ated CEXn pin. The frequency of the output is dependent on the timebase for the PCA counter/timer. The
duty cycle of the PWM output signal is varied using the module's PCA0CPLn capture/compare register.
When the value in the low byte of the PCA counter/timer (PCA0L) is equal to the value in PCA0CPLn, the
output on the CEXn pin will be set. When the count value in PCA0L overflows, the CEXn output will be
reset (see Figure 23.8). Also, when the counter/timer low byte (PCA0L) overflows from 0xFF to 0x00,
PCA0CPLn is reloaded automatically with the value stored in the module’s capture/compare high byte
(PCA0CPHn) without software intervention. Setting the ECOMn and PWMn bits in the PCA0CPMn register
enables 8-Bit Pulse Width Modulator mode. The duty cycle for 8-Bit PWM Mode is given by Equation 23.2.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Cap-
ture/Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the
ECOMn bit to ‘0’; writing to PCA0CPHn sets ECOMn to ‘1’.
Using Equation 23.2, the largest duty cycle is 100% (PCA0CPHn = 0), and the smallest duty cycle is
0.39% (PCA0CPHn = 0xFF). A 0% duty cycle may be generated by clearing the ECOMn bit to ‘0’.
214
PCA0CPLn
Write to
Reset
PCA0CPHn
Write to
0
ENB
ENB
1
W
P
M
1
6
n
0
O
M
E
C
n
Figure 23.8. PCA 8-Bit PWM Mode Diagram
PCA0CPMn
C
A
P
P
n
0 0 x 0
C
A
P
N
n
Equation 23.2. 8-Bit PWM Duty Cycle
M
A
T
n
O
G
T
n
W
DutyCycle
M
P
n
E
C
C
F
n
x
PCA Timebase
Enable
=
PCA0CPHn
Comparator
PCA0CPLn
Rev. 0.4
PCA0L
(
-------------------------------------------------- -
8-bit
256 PCA0CPHn
–
Overflow
256
match
S
R
SET
CLR
)
Q
Q
CEXn
Crossbar
Port I/O