HD64F2378RVFQ33 Renesas Electronics America, HD64F2378RVFQ33 Datasheet - Page 1200

• Manufacturer Part Number: HD64F2378RVFQ33
• Description: IC H8S MCU FLASH 512K 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of HD64F2378RVFQ33

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 33MHz
• Connectivity: I²C, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 97
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 6x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Index
DRAM Interface ..................................... 191
Effective Address...................................... 62
effective address extension ....................... 61
Effective Address Extension..................... 61
Exception Handling .................................. 93
Exception Handling Vector Table ............ 94
EXDMA controller (EXDMAC)
EXDMA Controller (EXDMAC) ........... 359
Extended Control Register (EXR) ............ 45
Flash Memory (0.18-μm F-ZTAT Version)
Rev.7.00 Mar. 18, 2009 page 1132 of 1136
REJ09B0109-0700
Single Address Mode.......................... 320
Transfer Mode .................................... 309
Write Data Buffer Function ................ 346
Interrupt Exception Handling ............... 98
Reset exception handling ...................... 95
Stack Status after Exception Handling 100
Trace Exception Handling .................... 98
Trap Instruction Exception Handling.... 99
Address Mode..................................... 375
Auto Request Mode ............................ 379
Block Transfer Mode .......................... 382
Burst Mode ......................................... 380
Cycle Steal Mode................................ 379
Dual Address Mode ............................ 375
Ending DMA Transfer ........................ 418
External Request Mode....................... 379
Normal Transfer Mode ....................... 381
Repeat Area Function ......................... 383
Single Address Mode.......................... 376
Boot Mode .......................................... 891
Communications Protocol................... 926
Error Protection .................................. 921
Flash MAT Configuration .................. 866
Hardware Protection ........................... 920
Mode Comparison .............................. 865
off-board programming mode............. 862
On-Board Programming ..................... 891
on-board programming mode ............. 862
Procedure Program ............................. 910
Programmer Mode .............................. 924
Flash Memory (0.35-μm F-ZTAT
Version) ..................................................833
General Registers ......................................44
I
I
Idle Cycle ................................................249
Input pull-up MOS ..................................455
Instruction Set ...........................................51
Interrupt Control Modes..........................127
2
2
C Bus Format .......................................786
C Bus Interface (IIC) ............................771
Protection ............................................920
Serial Communication Interface
Specification .......................................924
Software Protection.............................921
user boot MAT ....................................923
user boot memory MAT......................861
User Boot Mode..................................906
user MAT ............................................923
user memory MAT..............................861
User Program Mode ............................895
Boot Mode ..........................................846
Erase/Erase-Verify ..............................852
erasing units ........................................838
Error Protection...................................854
Hardware Protection ...........................854
Program/Program-Verify ....................850
Programmer Mode ..............................855
programming units ..............................838
programming/erasing in user program
mode....................................................849
Software Protection.............................854
Acknowledge ......................................771
Slave-address ......................................771
Arithmetic Operations Instructions .......54
Bit Manipulation Instructions ...............57
Block Data Transfer Instruction............61
Branch Instructions ...............................59
Data Transfer Instructions.....................53
Logic Operations Instructions ...............56
Shift Instructions ...................................56
System Control Instruction ...................60