ATA5773-PXQW Atmel, ATA5773-PXQW Datasheet - Page 160

• Manufacturer Part Number: ATA5773-PXQW
• Description: XMITTR UHF ASK/FSK 310MHZ 24VQFN
• Manufacturer: Atmel

Specifications of ATA5773-PXQW

• Frequency: 310MHz ~ 350MHz
• Modulation Or Protocol: UHF
• Power - Output: 8dBm
• Voltage - Supply: 2 V ~ 4 V
• Current - Transmitting: 9.8mA
• Data Interface: PCB, Surface Mount
• Memory Size: 4kB Flash, 256B EEPROM, 256B SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• Processor Series: ATA5x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Data Ram Size: 256 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

4.21.4
4.21.5
4.21.6
4.21.6.1
160
Atmel ATA5771/73/74
Software Break Points
Limitations of debugWIRE
Register Description
DWDR – debugWire Data Register
When designing a system where debugWIRE will be used, the following observations must be
made for correct operation:
• Pull-Up resistor on the dW/(RESET) line must be in the range of 10k to 20 k . However, the
• Connecting the RESET pin directly to V
• Capacitors inserted on the RESET pin must be disconnected when using debugWire.
• All external reset sources must be disconnected.
debugWIRE supports Program memory Break Points by the Atmel
Setting a Break Point in Atmel AVR Studio
memory. The instruction replaced by the BREAK instruction will be stored. When program
execution is continued, the stored instruction will be executed before continuing from the Pro-
gram memory. A break can be inserted manually by putting the BREAK instruction in the
program.
The Flash must be re-programmed each time a Break Point is changed. This is automatically
handled by AVR Studio through the debugWIRE interface. The use of Break Points will there-
fore reduce the Flash Data retention. Devices used for debugging purposes should not be
shipped to end customers.
The debugWIRE communication pin (dW) is physically located on the same pin as External
Reset (RESET). An External Reset source is therefore not supported when the debugWIRE is
enabled.
The debugWIRE system accurately emulates all I/O functions when running at full speed, i.e.,
when the program in the CPU is running. When the CPU is stopped, care must be taken while
accessing some of the I/O Registers via the debugger (AVR Studio). See the debugWIRE doc-
umentation for detailed description of the limitations.
A programmed DWEN Fuse enables some parts of the clock system to be running in all sleep
modes. This will increase the power consumption while in sleep. Thus, the DWEN Fuse
should be disabled when debugWire is not used.
The following section describes the registers used with the debugWire.
The DWDR Register provides a communication channel from the running program in the MCU
to the debugger. This register is only accessible by the debugWIRE and can therefore not be
used as a general purpose register in the normal operations.
Bit
0x27 (0x47)
Read/Write
Initial Value
pull-up resistor is optional.
R/W
7
0
R/W
6
0
R/W
5
0
CC
R/W
4
0
will not work.
®
DWDR[7:0]
will insert a BREAK instruction in the Program
R/W
3
0
R/W
2
0
®
R/W
AVR
1
0
®
Break instruction.
R/W
0
0
9137E–RKE–12/10
DWDR