XR17V352IB-0A-EVB Exar Corporation, XR17V352IB-0A-EVB Datasheet - Page 58
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
XR17V352IB-0A-EVB
Manufacturer Part Number
XR17V352IB-0A-EVB
Description
EVAL BOARD FOR XR17V352 113BGA
Manufacturer
Exar Corporation
Specifications of XR17V352IB-0A-EVB
Main Purpose
Interface, UART
Embedded
-
Utilized Ic / Part
XR17V352
Primary Attributes
-
Secondary Attributes
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
XR17V352
HIGH PERFORMANCE DUAL PCI EXPRESS UART
Enhanced features are enabled or disabled using this register. Bits [3:0] provide single or dual consecutive
character software flow control selection (see
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS or DSR Flow Control.
•
•
EFR[6]: Auto RTS or DTR Flow Control Enable
RTS#/DTR# output may be used for hardware flow control by setting EFR bit [6] to logic 1. When Auto RTS/
DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level
and RTS/DTR# will de-assert (HIGH) at the next upper trigger or selected hysteresis level. RTS/DTR# will re-
assert (LOW) when FIFO data falls below the next lower trigger or selected hysteresis level (see FCTR bits 4-
7). The RTS# or DTR# output must be asserted (LOW) before the auto RTS/DTR can take effect. The selection
for RTS# or DTR# is through MCR bit [2]. RTS/DTR# pin will function as a general purpose output when
hardware flow control is disabled.
•
•
EFR[5]: Special Character Detect Enable
•
•
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables the enhanced functions in IER bits [7:5], ISR bits [5:4], FCR
bits [5:4], MCR bits [7:5] and MSR [7:0] bits to be modified. After modifying any enhanced bits, EFR bit [4] can
be set to a logic 0 to latch the new values. This feature prevents legacy software from altering or overwriting
the enhanced functions once set. Normally, it is recommended to leave it enabled.
•
•
4.14
Logic 0 = Automatic CTS/DSR flow control is disabled (default).
Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts
(HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is
through MCR bit [2].
Logic 0 = Automatic RTS/DTR flow control is disabled (default).
Logic 1 = Enable Automatic RTS/DTR flow control.
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit [4] will be
set to indicate detection of the special character. bit [0] corresponds with the LSB bit for the receive
character. If flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special
character work normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow
control works normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special
character interrupt.
Logic 0 = Disable write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5] and MSR [7:0] bits. After a reset, all these bits are set to a logic 0 to be compatible with
ST16C550 mode (default).
Logic 1 = Enables write access to the enhanced function bits: IER bits [7:5], ISR bits [5:4], FCR bits [5:4],
MCR bits [7:5] and MSR [7:0] bits.
Enhanced Feature Register (EFR) - Read/Write
Table
19). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
58
REV. 1.0.1