OM13008,598 NXP Semiconductors, OM13008,598 Datasheet - Page 206
OM13008,598
Manufacturer Part Number
OM13008,598
Description
BOARD LPC XPRESSO LPC122X
Manufacturer
NXP Semiconductors
Series
LPCXpressor
Specifications of OM13008,598
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-6642
OM13008
OM13008
- Current page: 206 of 442
- Download datasheet (3Mb)
NXP Semiconductors
UM10441
User manual
Fig 25. Format and states in the Slave Transmitter mode
11.10.4 Slave Transmitter mode
reception of the own
Slave address and
one or more Data
bytes all are
acknowledged
last data byte
transmitted. Switched
to Not Addressed
Slave (AA bit in
I2CON = “0”)
arbitration lost as
Master and
addressed as Slave
DATA
n
In the slave transmitter mode, a number of data bytes are transmitted to a master receiver
(see
CON have been initialized, the I
address followed by the data direction bit which must be “1” (R) for the I
operate in the slave transmitter mode. After its own slave address and the R bit have been
received, the serial interrupt flag (SI) is set and a valid status code can be read from STAT.
This status code is used to vector to a state service routine, and the appropriate action to
be taken for each of these status codes is detailed in
mode may also be entered if arbitration is lost while the I
(see state 0xB0).
If the AA bit is reset during a transfer, the I
and enter state 0xC0 or 0xC8. The I
and will ignore the master receiver if it continues the transfer. Thus the master receiver
receives all 1s as serial data. While AA is reset, the I
slave address or a General Call address. However, the I
address recognition may be resumed at any time by setting AA. This means that the AA
bit may be used to temporarily isolate the I
A
Figure
S
from Master to Slave
from Slave to Master
any number of data bytes and their associated
Acknowledge bits
this number (contained in I2STA) corresponds to a defined state of
the I
25). Data transfer is initialized as in the slave receiver mode. When ADR and
2
C bus
SLA
All information provided in this document is subject to legal disclaimers.
Rev. 1.1 — 10 March 2011
R
A8H
B0H
A
A
2
C block waits until it is addressed by its own slave
DATA
2
C block is switched to the not addressed slave mode
B8H
2
C block will transmit the last byte of the transfer
A
2
C block from the I
Chapter 11: LPC122x I2C-bus controller
DATA
2
C block does not respond to its own
Table
C8H
C0H
2
A
A
2
C-bus is still monitored, and
C block is in the master mode
202. The slave transmitter
P OR S
ALL ONES
2
C-bus.
UM10441
P OR S
© NXP B.V. 2011. All rights reserved.
2
C block to
206 of 442
Related parts for OM13008,598
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: