P89LPC916FDH NXP Semiconductors, P89LPC916FDH Datasheet - Page 31

• Manufacturer Part Number: P89LPC916FDH
• Description: MCU 8BIT 80C51 2K FLASH, TSSOP16
• Manufacturer: NXP Semiconductors

Specifications of P89LPC916FDH

• Controller Family/series: (8051) 8052
• Core Size: 8bit
• No. Of I/o's: 14
• Program Memory Size: 2KB
• Ram Memory Size: 256Byte
• Cpu Speed: 18MHz
• Oscillator Type: Internal Only
• No. Of Timers: 4
• Digital Ic: RoHS Compliant

NXP Semiconductors
P89LPC915_916_917_5
Product data sheet
8.3.1 Clock definitions
8.3.2 CPU clock (OSCCLK)
8.3.3 Clock output (P89LPC917)
8.2 Enhanced CPU
8.3 Clocks
8.4 On-chip RC oscillator option
8.5 Watchdog oscillator option
The P89LPC915/916/917 uses an enhanced 80C51 CPU which runs at six times the
speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and
most instructions execute in one or two machine cycles.
The P89LPC915/916/917 device has several internal clocks as defined below:
OSCCLK — Input to the DIVM clock divider. OSCCLK is selected from one of four clock
sources (see
Section 8.8 “CCLK modification: DIVM
Note: f
CCLK — CPU clock; output of the clock divider. There are two CCLK cycles per machine
cycle, and most instructions are executed in one to two machine cycles (two or four CCLK
cycles).
RCCLK — The internal 7.373 MHz RC oscillator output.
PCLK — Clock for the various peripheral devices and is
The P89LPC915/916/917 provides several user-selectable oscillator options in generating
the CPU clock. This allows optimization for a range of needs from high precision to lowest
possible cost. These options are configured when the flash is programmed and include an
on-chip watchdog oscillator, an on-chip RC oscillator, and an external clock source.
The P89LPC917 supports a user-selectable clock output function on the CLKOUT pin.
This allows external devices to synchronize to the P89LPC917. This output is enabled by
the ENCLK bit in the TRIM register.
The frequency of this clock output is
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
The P89LPC915/916/917 has a 6-bit TRIM register that can be used to tune the
frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory
pre-programmed value to adjust the oscillator frequency to 7.373 MHz
temperature. End-user applications can write to the TRIM register to adjust the on-chip
RC oscillator to other frequencies. If CCLK is 8 MHz or slower, the CLKLP SFR bit
(AUXR1.7) can be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0
allowing highest performance access. This bit can then be set in software if CCLK is
running at 8 MHz or slower.
The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator
can be used to save power when a high clock frequency is not needed.
osc
is defined as the OSCCLK frequency.
Figure
11) and can also be optionally divided to a slower frequency (see
Rev. 05 — 15 December 2009
8-bit microcontrollers with accelerated two-clock 80C51 core
1
2
register”).
that of the CCLK. If the clock output is not needed
P89LPC915/916/917
CCLK
2
.
© NXP B.V. 2009. All rights reserved.
1 % at room
31 of 75