PIC16F872-E/SS Microchip Technology, PIC16F872-E/SS Datasheet - Page 266

• Manufacturer Part Number: PIC16F872-E/SS
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F872-E/SS

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SSOP
• Package: 28SSOP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 22
• Interface Type: I2C/SPI
• On-chip Adc: 5-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
DS31016A-page 16-16
The SSP module has five registers for I
• SSP Control Register (SSPCON)
• SSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer (SSPBUF)
• SSP Shift Register (SSPSR) - Not directly accessible
• SSP Address Register (SSPADD)
The SSPCON register allows control of the I
(SSPCON<3:0>) allow one of the following I
• I
• I
• I
• I
• I
Before selecting any I
the appropriate TRIS bits. Selecting an I
and SDA pins to be used as the clock and data lines in I
The SSPSTAT register gives the status of the data transfer. This information includes detection
of a START or STOP bit, specifies if the received byte was data or address, if the next byte is the
completion of 10-bit address, and if this will be a read or write data transfer. The SSPSTAT reg-
ister is read only.
The SSPBUF is the register to which transfer data is written to or read from. The SSPSR register
shifts the data in or out of the device. In receive operations, the SSPBUF and SSPSR create a
doubled buffered receiver. This allows reception of the next byte to begin before reading the last
byte of received data. When the complete byte is received, it is transferred to the SSPBUF reg-
ister and the SSPIF flag bit is set. If another complete byte is received before the SSPBUF reg-
ister is read, a receiver overflow has occurred and bit SSPOV (SSPCON<6>) is set.
The SSPADD register holds the slave address. In 10-bit mode, the user needs to write the high
byte of the address (1111 0 A9 A8 0). Following the high byte address match, the low byte of
the address needs to be loaded (A7:A0).
enabled)
enabled)
2
2
2
2
2
C Slave mode (7-bit address)
C Slave mode (10-bit address)
C Firmware controlled Multi-Master mode, 7-bit address (start and stop bit interrupts
C Firmware controlled Multi-Master mode, 10-bit address (start and stop bit interrupts
C Firmware controlled Master mode, slave is idle
2
C mode, the SCL and SDA pins must be programmed to inputs by setting
2
C operation. They are:
2
C mode, by setting the SSPEN bit, enables the SCL
2
C modes to be selected:
2
C operation. Four mode selection bits
2
C mode.
1997 Microchip Technology Inc.