DS3181 Maxim Integrated Products, DS3181 Datasheet - Page 97
DS3181
Manufacturer Part Number
DS3181
Description
Network Controller & Processor ICs DS3-E3 ATM-Packet PH Y with Built-in Line
Manufacturer
Maxim Integrated Products
Datasheet
1.DS3184DK.pdf
(400 pages)
Specifications of DS3181
Product
Framer
Number Of Transceivers
1
Data Rate
44.736 Mbps
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
280 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Package / Case
TEBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 97 of 400
- Download datasheet (4Mb)
DS3181/DS3182/DS3183/DS3184
latched status register bits in clear on read mode are carefully designed not to miss events that occur while a
register is being read when the latched bit has not already been set. See
Figure 8-46
and
Figure 8-47.
10.1.6 Global Write Method
All of the ports can be written to simultaneously using the global write method. This method is enabled by setting
the GL.CR1.GWM bit. When the global write method is enabled, a write to a register on any valid port will write to
the same register on all valid ports. A valid port is a port that is available in a particular packaged part. For
example, port four would not be valid in a DS3183 device. After reset, the global write method is not enabled.
When the GWM bit is set, read data from the port registers is not valid and read data from the global and test
registers is valid. The data value read back from a port register should be ignored.
10.1.7 Interrupt and Pin Modes
The interrupt (INT) pin is configurable to drive high or float when not active. The GL.CR1.INTM bit controls the pin
configuration, when it is set the INT pin will drive high when not active. After reset, the INT pin will be in high
impedance mode until an interrupt source is active and enabled to drive the interrupt pin.
10.1.8 Interrupt Structure
The interrupt structure is designed to efficiently guide the user to the source of an enabled interrupt source. The
status bits in the global status (GL.SR) and global status latched register (GL.SRL) are read to determine if the
interrupt source is a global event like the UTOPIA/POS-PHY interface, global performance monitor update or
whether it came from one of the ports. If the interrupt event came from one of the ports then the port status register
(PORT.SR) and port status register latched (PORT.SRL) can be read to determine if the interrupt source is a
common port event like the performance monitor update or LIU or whether it came from one of the DS3/E3
Framers, PLCP Framer, ATM/PKT, BERT, HDLC, FEAC or Trail Trace status registers. If the interrupt came from
one of the DS3/E3 Framers, PLCP Framer, ATM/PKT, BERT, HDLC, FEAC or Trail Trace status registers, then
one of those registers will need to be read to determine the event that caused the interrupt.
The source of an interrupt can be determined by reading three status registers: global, port and block status
registers.
When a mode is not enabled, then interrupts from that source will not occur. For example, if PLCP framing is not
enabled then the potential interrupts from the latched status register in the PLCP block cannot occur. Similarly, if
E3 framing mode is enabled, an interrupt source that is defined in DS3 framing, but not in E3 framing, cannot
create a new interrupt. Note that when modes are changed, the latched status bits of the new mode, as well as any
other mode, may get set. If the data path reset is set during or after the mode change, the latched status bits will be
automatically cleared. If the data path reset is not used to clear the latched status bits, then the registers must be
cleared by reading or writing to them based on the register clear method selected.
97
Related parts for DS3181
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: