COM20022I3V-HD SMSC, COM20022I3V-HD Datasheet - Page 43

• Manufacturer Part Number: COM20022I3V-HD
• Description: Network Controller & Processor ICs ARCNET Contrllr
• Manufacturer: SMSC

Specifications of COM20022I3V-HD

• Data Rate: 10 Mbps
• Supply Voltage (max): 3.465 V
• Supply Voltage (min): 3.135 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Board RAM
Datasheet
SMSC COM20022I 3V
BIT
5,4
7
6
3
2
Read Bus Timing
Select
Reserved
Clock Multiplier
Enhanced
Functions
No Synchronous
BIT NAME
RBUSTMG This bit is used to Disable/Enable the High Speed CPU
CKUP1, 0
EF
NOSYNC
SYMBOL
Table 6.13 - Setup 2 Register
DATASHEET
Read function for High Speed CPU bus support.
RBUSTMG=0: Disable (Default), RBUSTMG=1: Enable.
That is, if BUSTMG (pin 26) = 1 and RBUSTMG = 1, High
Speed CPU Read operations are enabled. It does not
influence write operation. High speed CPU Read operation
is only for non-multiplexed bus.
This bit is undefined.
Higher frequency clocks are generated from the 20 MHz
crystal through the selection of these two bits as shown.
This clock multiplier is powered-down on default. After
changing the CKUP1 and CKUP0 bits, the ARCNET core
operation is stopped and the internal PLL in the clock
multiplier is awakened and it starts to generate the 40 MHz.
The lock out time of the internal PLL is 8μSec typically.
After 1 mS it is necessary to write command data '18H' to
command register for re-starting the ARCNET core
operation. EF bit must be ‘1’ if the data rate is over 5Mbps.
CAUTION: Changing the CKUP1 and CKUP0 bits must be
one time or less after releasing a hardware reset.
CKUP1
Note: After changing the CKUP1 or CKUP0 bits, it is
These initializing steps are shown below.
1.
2.
3.
4.
5.
This bit is used to enable the new enhanced functions in the
COM20022I 3V. EF = 0: Disable (Default), EF = 1: Enable.
If EF = 0, the timing and function is the same as in the
COM20020, Revision B. See appendix “A”. EF bit must be
‘1’ if the data rate is over 5Mbps.
EF bit should be ‘1’ for new design customers.
EF bit should be ‘0’ for replacement customers.
This bit is used to enable the SYNC command during
initialization. NOSYNC= 0, Enable (Default) The line must
be idle for the RAM initialization sequence to be written.
NOSYNC= 1, Disable:) The line does not have to be idle for
the RAM initialization sequence to be written. See appendix
“A”.
Hardware reset (Power ON)
Change CKUP[1, 0] bit
Wait 1mSec (wait until stable oscillation)
Write command '18H' (start internal operation)
Start initializing routine (Execute existing software)
0
0
1
1
Page 43
necessary to write a command data '18H' to the
command register. Because after changing the
CKUP [1, 0] bits, the internal operation is stopped
temporarily. The writing of the command is to start
the operation.
CKUP0
0
1
0
1
DESCRIPTION
Clock Frequency (Data Rate)
20 MHz (Up to 2.5Mbps) Default
40 MHz (Up to 5Mbps)
Reserved
80 MHz (Only 10Mbps)
Revision 02-27-06