PEB3265FV15XP Infineon Technologies, PEB3265FV15XP Datasheet - Page 72
PEB3265FV15XP
Manufacturer Part Number
PEB3265FV15XP
Description
Manufacturer
Infineon Technologies
Datasheet
1.PEB3265FV15XP.pdf
(383 pages)
Specifications of PEB3265FV15XP
On-hook Transmission
Yes
Polarity Reversal
Yes
On-chip Ring Relay Driver
Yes
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
TQFP
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Operating Supply Voltage (max)
3.465V
Operating Supply Voltage (min)
3.135V
Lead Free Status / RoHS Status
Compliant
- Current page: 72 of 383
- Download datasheet (6Mb)
Preliminary
3.9
Message Waiting Indication (MWI) is usually performed using a glow lamp at the
subscriber phone. Current does not flow through a glow lamp until the voltage reaches
a threshold value above approximately 80 V. At this threshold, the neon gas in the lamp
will start to glow. When the voltage is reduced, the current falls under a certain threshold
and the lamp glow is extinguished. DuSLIC has high-voltage SLIC technology (170 V)
which is able to activate the glow lamp without any external components.
The hardware circuitry is shown in
telephone circuit with the hook switch in the on-hook mode, together with the
impedances for the on-hook (Z
Figure 36
The glow lamp circuit also requires a resistor (R
phone. When activated, the lamp must be able to either blink or remain on constantly.
In non-DuSLIC solutions the telephone ringer may respond briefly if the signal slope is
too steep, which is not desirable. DuSLIC’s integrated ramp generator can be
programmed to increase the voltage slowly, to ensure activating the lamp and not the
ringer.
Data Sheet
Message Waiting Indication (only DuSLIC-E/-E2/-P)
MWI Circuitry with Glow Lamp
Z
L
R
) and off-hook (Z
Z
R
Figure 36
R
MW
Lamp
MW
72
MW
Z
Z
R
L
L
R
MW
) modes.
) and a lamp (MW Lamp) built into the
below. The figure shows a typical
AC Impedance
Ringer Impedance
Pre Resistor Message Waiting
Functional Description
ezm14066.wmf
2000-07-14
DuSLIC
Related parts for PEB3265FV15XP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Filter, Dual Channel Subscriber Line Interface Codec Filter
Manufacturer:
Infineon Technologies AG
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
(PEB326x / PEB426x) Dual Channel Slicofi-2 / Slic Duslic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
16-bit microcontroller with 2x2 KByte RAM
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet: