ICS1523M IDT, Integrated Device Technology Inc, ICS1523M Datasheet - Page 3

• Manufacturer Part Number: ICS1523M
• Description: IC VIDEO CLK SYNTHESIZER 24-SOIC
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Clock/Frequency Synthesizer (IF), Fanout Distribution, Frequency Generatorr

Specifications of ICS1523M

• Pll: Yes
• Input: Clock
• Output: LVPECL, SSTL-3
• Number Of Circuits: 1
• Ratio - Input:output: 1:3
• Differential - Input:output: No/Yes
• Frequency - Max: 250MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Frequency-max: 250MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 1523M

MDS ICS1523 ZC
MHz even if a low output frequency is required.The
output of the VCOD is the full speed output frequency
seen on the CLK pins.
1.7 Dynamic Phase Adjust (DPA)
The VCOD output clock is then sent through the DPA
for phase adjustment relative to the input HSYNC as
well as the 12-bit internal Feedback Divider. An
external divider may alternately be used and it’s output
must be input on the EXTFB pin. The feedback divider
controls how many clocks are seen during every cycle
of the input reference.
The DPA allows a programmable delay between the
input HSYNC to the clock and FUNC outputs, relative
to the input HSYNC signal on a sub-pixel basis. A delay
of up to one clock period is programmable: See Note 6
in
information.
1.8 Feedback Divider (FD) and FUNC
The 12-bit FD controls how many clocks are seen
between successive HSYNCs.
The number of clocks per HSYNC is FB + 8
The FD output is a 4 CLK wide, active high signal
called FUNC. The FUNC signal is aligned with the
output clocks via the DPA and is intended to be used by
the system as a replacement for the HSYNC input,
which is of in-determinate quality and is not aligned
with the output clocks. Alternately, the post
Schmitt-trigger HSYNC signal can also be DPA
delayed and then output on the FUNC pin. See 0x0:5.
1.9 Phase Frequency Detector (PFD)
The PFD compares the FUNC signal to the selected
input described below and controls the filter voltage by
enabling and disabling the charge pump. The charge
pump has programmable current drive and will source
and sink current as appropriate to keep the input and
the FUNC output aligned.
1.10 HSYNC and REF Inputs
One of the PFDs two possible inputs is HSYNC (pin 7).
HSYNC is conditioned by a high-performance
Schmitt-trigger. This preconditioned HSYNC signal,
called REF, is provided as a reference signal with a
short transition time. REF can be output on pin 14.
Section 5, “Register Set Details”
Integrated Device Technology, Inc.
for more

3
Tech Support: www.idt.com/go/clockhelp
Video Clock Synthesizer with I
1.11 OSC Input
The high-frequency OSC input pin, has a 7-bit user
programmable divider. OSC can also be selected as
the loop input, allowing the loop to operate from any
appropriate, single-ended source, typically a crystal
oscillator.
1.12 FUNC Output
Either the conditioned HSYNC input or the loop output
(recovered HSYNC) is available at the FUNC pin, and
is aligned with the output clocks.
1.13 Logic Inputs
The ICS1523 uses Low-Voltage TTL (LVTTL) inputs
that are 5 volt tolerant such as most VESA compliant
HSYNC and VSYNC signals.
1.14 Output Drivers
The ICS1523 also has SSTL_3 (EIA/JESD8-8) and
low-voltage PECL (Positive ECL) outputs, operating off
the 3.3 V supply voltage.
The SSTL_3 and differential PECL output drivers drive
resistive terminations or transmission lines. At lower
clock frequencies, the SSTL_3 outputs can be
operated unterminated. See
Termination”
1.15 Power-On Reset Detection (POR)
The ICS1523 has automatic POR circuitry, meaning it
resets itself if the supply voltage drops below a
threshold values of approximately 1.8 V. No external
connection to a reset signal is required.
1.16 I
The ICS1523 uses a 5 V tolerant, industry-standard
I
(100 kHz) or high speed (400 kHz). The interface uses
12 indexed registers: one write-only, eight read/write,
and three read-only registers.
Two ICS1523 devices can be addressed according to
the state of the I2CADR pin. When this pin is low the
read address is 4Dh and the write address is 4Ch.
When the pin is high, the read address is 4Fh and the
write address is 4Eh. See
2
C-bus serial interface that runs at either low speed
2
C Bus Serial Interface
Section 11,
2
Section 9, “Output
C Programmable Delay
“Programming”.
Revision 020811
ICS1523