EP3C120F780C8N Altera, EP3C120F780C8N Datasheet - Page 240

• Manufacturer Part Number: EP3C120F780C8N
• Description: IC CYCLONE III FPGA 119K 780FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F780C8N

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 531
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 531
• Frequency (max): 402MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FBGA
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2392; 544-2533; 544-2533; EP3C120F780C8NES

9–80
Cyclone III Device Handbook, Volume 1
When you use the AP configuration in Cyclone III devices, the Cyclone III device
loads the default factory configuration located at the following address after device
power-up in remote update mode:
boot_address[23:0] = 24'h010000 = 24'b1 0000 0000 0000 0000
You can change the default factory configuration address to any desired address using
the APFC_BOOT_ADDR JTAG instruction. The factory configuration image is stored in
non-volatile memory and is never updated or modified using remote access. This
corresponds to the default start address location 0x010000 represented in 16-bit word
addressing (or the updated address if the default address is changed) in the
supported parallel flash memory. For more information about the application of the
APFC_BOOT_ADDR JTAG instruction in AP configuration scheme, refer to
Instructions” on page
The factory configuration image is user designed and contains soft logic (Nios II
processor or state machine and the remote communication interface) to:
■
■
■
■
■
Figure 9–34
in remote update mode.
Figure 9–34. Transitions Between Configurations in Remote Update Mode
Process any errors based on status information from the dedicated remote system
upgrade circuitry
Communicate with the remote host and receive new application configurations
and store the new configuration data in the local non-volatile memory device
Determine which application configuration is to be loaded into the Cyclone III
device family
Enable or disable the user watchdog timer and load its time-out value (optional)
Instruct the dedicated remote system upgrade circuitry to start a reconfiguration
cycle
Configuration
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
Error
Power Up
shows the transitions between the factory and application configurations
9–61.
Configuration
Factory
Configuration Error
Set Control Register
Configuration Error
and Reconfigure
Set Control Register
and Reconfigure
Reload a Different Application
Reload a Different Application
© December 2009 Altera Corporation
Application 1
Configuration
Configuration
Application n
Remote System Upgrade
“JTAG