AT89C51CC01 Atmel Corporation, AT89C51CC01 Datasheet - Page 77
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT89C51CC01
Manufacturer Part Number
AT89C51CC01
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT89C51CC01.pdf
(167 pages)
2.AT89C51CC01.pdf
(12 pages)
3.AT89C51CC01.pdf
(32 pages)
4.AT89C51CC01.pdf
(29 pages)
Specifications of AT89C51CC01
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
40 MHz
Cpu
8051-12C
Max I/o Pins
34
Uart
1
Can
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
62.5
Sram (kbytes)
1.25
Eeprom (bytes)
2048
Self Program Memory
API
Operating Voltage (vcc)
3.0 to 5.5
Timers
4
Isp
UART/CAN
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT89C51CC01CA-IM
Manufacturer:
ATMEL
Quantity:
831
Company:
Part Number:
AT89C51CC01CA-RLTUM
Manufacturer:
ATMEL
Quantity:
4 000
Company:
Part Number:
AT89C51CC01CA-RLTUM
Manufacturer:
Atmel
Quantity:
3 136
Company:
Part Number:
AT89C51CC01CA-SLIM
Manufacturer:
ATMEL
Quantity:
11
Company:
Part Number:
AT89C51CC01CA-SLSUM
Manufacturer:
ATMEL
Quantity:
2 916
Part Number:
AT89C51CC01UA-RLTUM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT89C51CC01UA-UM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Figure 41. CAN Bit Construction
Synchronization Segment
Propagation Time Segment
Phase Segment 1
Sample Point
Phase Segment 2
Information Processing Time
Bit Lengthening
4129N–CAN–03/08
Transmission Point
Time Quantum
CAN Frame
(consumer)
(producer)
(producer)
Segments
Segments
(producer)
(producer)
The first segment is used to synchronize the various bus nodes.
On transmission, at the start of this segment, the current bit level is output. If there is a
bit state change between the previous bit and the current bit, then the bus state change
is expected to occur within this segment by the receiving nodes.
This segment is used to compensate for signal delays across the network.
This is necessary to compensate for signal propagation delays on the bus line and
through the transceivers of the bus nodes.
Phase Segment 1 is used to compensate for edge phase errors.
This segment may be lengthened during resynchronization.
The sample point is the point of time at which the bus level is read and interpreted as the
value of the respective bit. Its location is at the end of Phase Segment 1 (between the
two Phase Segments).
This segment is also used to compensate for edge phase errors.
This segment may be shortened during resynchronization, but the length has to be at
least as long as the information processing time and may not be more than the length of
Phase Segment 1.
It is the time required for the logic to determine the bit level of a sampled bit.
The Information processing Time begins at the sample point, is measured in TQ and is
fixed at 2 TQ for the Atmel CAN. Since Phase Segment 2 also begins at the sample
point and is the last segment in the bit time, Phase Segment 2 minimum shall not be
less than the Information processing Time.
As a result of resynchronization, Phase Segment 1 may be lengthened or Phase Seg-
ment 2 may be shortened to compensate for oscillator tolerances. If, for example, the
transmitter oscillator is slower than the receiver oscillator, the next falling edge used for
resynchronization may be delayed. So Phase Segment 1 is lengthened in order to
adjust the sample point and the end of the bit time.
SYNC_SEG
propagation
delay
SYNC_SEG
PROP_SEG
PROP_SEG
Nominal CAN Bit Time
PHASE_SEG_1
PHASE_SEG_1
PHASE_SEG_2
Sample Point
PHASE_SEG_2
77