AT89C51CC01 Atmel Corporation, AT89C51CC01 Datasheet - Page 83

no-image

AT89C51CC01

Manufacturer Part Number
AT89C51CC01
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of AT89C51CC01

Flash (kbytes)
32 Kbytes
Max. Operating Frequency
40 MHz
Cpu
8051-12C
Max I/o Pins
34
Uart
1
Can
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
62.5
Sram (kbytes)
1.25
Eeprom (bytes)
2048
Self Program Memory
API
Operating Voltage (vcc)
3.0 to 5.5
Timers
4
Isp
UART/CAN
Watchdog
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT89C51CC01CA-IM
Manufacturer:
ATMEL
Quantity:
831
Part Number:
AT89C51CC01CA-RLTUM
Manufacturer:
ATMEL
Quantity:
4 000
Part Number:
AT89C51CC01CA-RLTUM
Manufacturer:
Atmel
Quantity:
3 136
Part Number:
AT89C51CC01CA-RLTUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT89C51CC01CA-SLIM
Manufacturer:
ATMEL
Quantity:
11
Part Number:
AT89C51CC01CA-SLSUM
Manufacturer:
ATMEL
Quantity:
2 916
Part Number:
AT89C51CC01CA-SLSUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT89C51CC01UA-RLRUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT89C51CC01UA-RLTUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT89C51CC01UA-RLTUM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT89C51CC01UA-SLSUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT89C51CC01UA-UM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Buffer Mode
4129N–CAN–03/08
Any message object can be used to define one buffer, including non-consecutive mes-
sage objects, and with no limitation in number of message objects used up to 15.
Each message object of the buffer must be initialized CONCH2 = 1 and CONCH1 = 1;
Figure 45. Buffer mode
The same acceptance filter must be defined for each message objects of the buffer.
When there is no mask on the identifier or the IDE, all messages are accepted.
A received frame will always be stored in the lowest free message object.
When the flag Rxok is set on one of the buffer message objects, this message object
can then be read by the application. This flag must then be cleared by the software and
the message object re-enabled in buffer reception in order to free the message object.
The OVRBUF flag in the CANGIT register is set when the buffer is full. This flag can
generate an interrupt.
The frames following the buffer-full interrupt will not stored and no status will be over-
written in the CANSTCH registers involved in the buffer until at least one of the buffer
message objects is re-enabled in reception.
This flag must be cleared by the software in order to acknowledge the interrupt.
message object 14
message object 13
message object 12
message object 11
message object 10
message object 9
message object 8
message object 7
message object 6
message object 5
message object 4
message object 3
message object 2
message object 1
message object 0
Block buffer
buffer 7
buffer 6
buffer 5
buffer 4
buffer 3
buffer 2
buffer 1
buffer 0
83

Related parts for AT89C51CC01