ATmega644R212 Atmel Corporation, ATmega644R212 Datasheet - Page 18
ATmega644R212
Manufacturer Part Number
ATmega644R212
Description
Manufacturer
Atmel Corporation
Specifications of ATmega644R212
Flash (kbytes)
64 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
4
Eeprom (bytes)
2048
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
- Current page: 18 of 198
- Download datasheet (5Mb)
AT86RF231
The SPI is based on a byte-oriented protocol and is always a bidirectional communication
between master and slave. The SPI master starts the transfer by asserting /SEL = L. Then the
master generates eight SPI clock cycles to transfer one byte to the radio transceiver (via MOSI).
At the same time, the slave transmits one byte to the master (via MISO). When the master wants
to receive one byte of data from the slave it must also transmit one byte to the slave. All bytes
are transferred with MSB first. An SPI transaction is finished by releasing /SEL = H.
An SPI register access consists of two bytes, a Frame Buffer or SRAM access of at least two or
more bytes as described in
Section 6.2 “SPI Protocol” on page
19.
/SEL = L enables the MISO output driver of the AT86RF231. The MSB of MISO is valid after t1
(see
Section 12.4 “Digital Interface Timing Characteristics” on page 157
parameter 12.4.3) and
is updated at each falling edge of SCLK. If the driver is disabled, there is no internal pull-up cir-
cuitry connected to it. Driving the appropriate signal level must be ensured by the master device
or an external pull-up resistor. Note, when both /SEL and /RST are active, the MISO output
driver is also enabled.
Referring to
Figure 6-2 on page 17
and
Figure 6-3 on page 17
MOSI is sampled at the rising
edge of the SCLK signal and the output is set at the falling edge of SCLK. The signal must be
stable before and after the rising edge of SCLK as specified by t
and t
, refer to
Section 12.4
3
4
“Digital Interface Timing Characteristics” on page 157
parameters 12.4.5 and 12.4.6.
This SPI operational mode is commonly known as "SPI mode 0".
18
8111C–MCU Wireless–09/09
Related parts for ATmega644R212
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: