ATmega644R212 Atmel Corporation, ATmega644R212 Datasheet - Page 99
ATmega644R212
Manufacturer Part Number
ATmega644R212
Description
Manufacturer
Atmel Corporation
Specifications of ATmega644R212
Flash (kbytes)
64 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
4
Eeprom (bytes)
2048
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
- Current page: 99 of 198
- Download datasheet (5Mb)
8.6
8.6.1
8111C–MCU Wireless–09/09
Link Quality Indication (LQI)
Overview
According to IEEE 802.15.4, the LQI measurement is a characterization of the strength and/or
quality of a received packet. The measurement may be implemented using receiver ED, a sig-
nal-to-noise ratio estimation, or a combination of these methods. The use of the LQI result by the
network or application layers is not specified in this standard. LQI values shall be an integer
ranging from 0x00 to 0xFF. The minimum and maximum LQI values (0x00 and 0xFF) should be
associated with the lowest and highest quality compliant signals, respectively, and LQI values in
between should be uniformly distributed between these two limits.
The LQI measurement of the AT86RF231 is implemented as a measure of the link quality which
can be described with the packet error rate (PER) for this link. An LQI value can be associated
with an expected packet error rate. The PER is the ratio of erroneous received frames to the
total number of received frames. A PER of zero indicates no frame error, whereas at a PER of
one no frame was received correctly.
The radio transceiver uses correlation results of multiple symbols within a frame to determine
the LQI value. This is done for each received frame. The minimum frame length for a valid LQI
value is two octets PSDU. LQI values are integers ranging from 0 to 255.
As an example,
tain LQI value.
Figure 8-6.
The values are taken from received frames of PSDU length of 20 octets on transmission chan-
nels with reasonable low multipath delay spreads. If the transmission channel characteristic has
higher multipath delay spread than assumed in the example, the PER is slightly higher for a cer-
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1
0
Conditional Packet Error Rate versus LQI
Figure 8-6 on page 99
50
100
LQI
shows the conditional packet error when receiving a cer-
150
200
250
AT86RF231
99
Related parts for ATmega644R212
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: