ATtiny26 Atmel Corporation, ATtiny26 Datasheet - Page 116
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny26
Manufacturer Part Number
ATtiny26
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny26
Flash (kbytes)
2 Kbytes
Pin Count
20
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
16
Ext Interrupts
11
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.12
Eeprom (bytes)
128
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATTINY26
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny26-16MI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny26-16MU
Manufacturer:
ATMEL
Quantity:
7 119
Part Number:
ATtiny26-16SC
Manufacturer:
MITEL
Quantity:
20 000
Part Number:
ATtiny26-16SI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny26-16SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny26-8PI
Manufacturer:
UTC
Quantity:
15
Company:
Part Number:
ATtiny26-8SI
Manufacturer:
INTEL
Quantity:
8
Company:
Part Number:
ATtiny26-8SU
Manufacturer:
ATMTLL
Quantity:
5 510
Company:
Part Number:
ATtiny26-8SU
Manufacturer:
SIEMENS
Quantity:
5 510
Reading the Flash
Reading the EEPROM
Programming the
Fuse Low Bits
116
ATtiny26(L)
Figure 61. Programming the EEPROM Waveforms
The algorithm for reading the Flash memory is as follows (refer to “Programming the Flash” on
page 113 for details on Command and Address loading):
1. A: Load Command “0000 0010”.
2. F: Load Address High Byte ($00 - $03).
3. B: Load Address Low Byte ($00 - $FF).
4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA.
5. Set BS1 to “1”. The Flash word high byte can now be read at DATA.
6. Set OE to “1”.
The algorithm for reading the EEPROM memory is as follows (refer to “Programming the Flash”
on page 113 for details on Command and Address loading):
1. A: Load Command “0000 0011”.
2. B: Load Address Low Byte ($00 - $FF).
3. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at DATA.
4. Set OE to “1”.
The algorithm for programming the Fuse Low bits is as follows (refer to “Programming the Flash”
on page 113 for details on Command and Data loading):
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Set BS1 and BS2 to “0”.
4. Give WR a negative pulse and wait for RDY/BSY to go high.
RESET +12V
PAGEL/BS1
RDY/BSY
XA1/BS2
XTAL1
DATA
XA0
WR
OE
$11
A
ADDR. LOW
B
DATA
C
ADDR. LOW
B
J
DATA
C
XX
K
1477K–AVR–08/10