M55800A Atmel Corporation, M55800A Datasheet - Page 204

• Manufacturer Part Number: M55800A
• Manufacturer: Atmel Corporation

Specifications of M55800A

• Flash (kbytes): 0 Kbytes
• Pin Count: 176
• Max. Operating Frequency: 33 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 58
• Ext Interrupts: 58
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 3
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 72
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3/5.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.7.5
Register Name:
Access Type:
Reset State:
Offset:
• RDRF: Receive Data Register Full (Code Label SP_RDRF)
0 = No data has been received since the last read of SP_RDR.
1 = Data has been received and the received data has been transferred from the serializer to SP_RDR since the last read
of SP_RDR.
• TDRE: Transmit Data Register Empty (Code Label SP_TDRE)
0 = Data has been written to SP_TDR and not yet transferred to the serializer.
1 = The last data written in the Transmit Data Register has been transferred in the serializer.
TDRE equals zero when the SPI is disabled or at reset. The SPI enable command sets this bit to one.
• MODF: Mode Fault Error (Code Label SP_MODF)
0 = No Mode Fault has been detected since the last read of SP_SR.
1 = A Mode Fault occurred since the last read of the SP_SR.
• OVRES: Overrun Error Status (Code Label SP_OVRES)
0 = No overrun has been detected since the last read of SP_SR.
1 = An overrun has occurred since the last read of SP_SR.
An overrun occurs when SP_RDR is loaded at least twice from the serializer since the last read of the SP_RDR.
• SPENDRX: End of Receiver Transfer (Code Label SP_ENDRX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the receiver is active.
• SPENDTX: End of Transmitter Transfer (Code Label SP_ENDTX)
0 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is inactive.
1 = The End of Transfer signal from the Peripheral Data Controller channel dedicated to the transmitter is active.
• SPIENS: SPI Enable Status (Code Label SP_SPIENS)
0 = SPI is disabled.
1 = SPI is enabled.
204
31
23
15
–
–
–
7
–
AT91M5880A
SPI Status Register
SP_SR
Read-only
0
0x10
30
22
14
–
–
–
6
–
SPENDTX
29
21
13
–
–
–
5
SPENDRX
28
20
12
–
–
–
4
OVRES
27
19
11
–
–
–
3
MODF
26
18
10
–
–
–
2
TDRE
25
17
–
–
–
9
1
1745F–ATARM–06-Sep-07
SPIENS
RDRF
24
16
–
8
–
0