AD7294 Analog Devices, AD7294 Datasheet - Page 12

• Manufacturer Part Number: AD7294
• Description: 12-Bit Monitor and Control System with Multichannel ADC, DACs, Temperature Sensor, and Current Sense
• Manufacturer: Analog Devices

Specifications of AD7294

• Resolution (bits): 12bit
• # Chan: 9
• Sample Rate: 200kSPS
• Interface: I²C/Ser 2-Wire,Ser
• Analog Input Type: Diff-Uni,SE-Uni
• Ain Range: (Vref) p-p,2 V p-p,Uni (Vref),Uni (Vref) x 2
• Adc Architecture: SAR
• Pkg Type: CSP

AD7294
Table 7. Pin Function Descriptions
TQFP Pin No.
2, 61
3, 60
1, 4, 16, 17, 32,
33, 59, 64
5, 8, 14, 25, 56, 57
6, 7, 13, 24, 34,
55, 58
9, 12
10, 11
15
18, 23, 26, 31
19, 22, 27, 30
20, 29
21, 28
35
38, 37, 36
39
LFCSP Pin No.
1, 54
2, 53
3, 52
4, 7, 13, 22, 50
5, 6 12, 21, 29, 49,
51
8, 11
9, 10
14
15, 20 23,28
16, 19, 24, 27
17, 26
18, 25
30
33, 32, 31
34
Mnemonic
RS2(−), RS1(−)
RS2(+), RS1(+)
NC
AV
for TQFP; AV
to AV
LFCSP
AGND1 to
AGND7
D2(−), D1(−)
D2(+), D1(+)
REF
OFFSET IN A to
OFFSET IN D
V
DAC OUT GND
AB, DAC OUT
GND CD
DAC OUTV+ AB,
DAC OUTV+ CD
ALERT/BUSY
AS0, AS1, AS2
SDA
OUT
DD
OUT
A to V
1 to AV
DD
/REF
4 for
OUT
IN
DD
DD
DAC
D
6
1
Rev. H | Page 12 of 48
Description
Connection for External Shunt Resistor.
Connection for External Shunt Resistor.
No Connection. Do not connect these pins.
Analog Supply Pins. The operating range is 4.5 V to 5.5 V. These pins provide
the supply voltage for all the analog circuitry on the AD7294. Connect the
AV
potential. This supply should be decoupled to AGND with one 10 µF tantalum
capacitor and a 0.1 µF ceramic capacitor for each AV
Analog Ground. Ground reference point for all analog circuitry on the AD7294.
Refer all analog input signals and any external reference signal to this AGND
voltage. Connect all seven of these AGND pins to the AGND plane of the
system. Note that AGND5 is a DAC ground reference point and should be used
as a star ground for circuitry being driven by the DAC outputs. Ideally, the
AGND and DGND voltages should be at the same potential and must not be
more than 0.3 V apart, even on a transient basis.
Temperature Sensor Analog Input. These pins are connected to the external
temperature sensing transistor. See Figure 46 and Figure 47.
Temperature Sensor Analog Input. These pins are connected to the external
temperature sensing transistor. See Figure 46 and Figure 47.
DAC Reference Output/Input Pin. The REF
four DAC channels. On power-up, the default configuration of this pin is
external reference (REF
power-down register; see Table 27. Decoupling capacitors (220 nF
recommended) are connected to this pin to decouple the reference buffer.
Provided the output is buffered, the on-chip reference can be taken from this
pin and applied externally to the rest of a system. A maximum external
reference voltage of AV
REF
DAC Analog Offset Input Pins. These pins set the desired output range for each
DAC channel. The DACs have an output voltage span of 5 V, which can be
shifted from 0 V to 5 V to a maximum output voltage of 10 V to 15 V by
supplying an offset voltage to these pins. These pins can be left floating, in
which case decouple them to AGND with a 100 nF capacitor.
Buffered Analog DAC Outputs for Channel A to Channel D. Each DAC analog
output is driven from an output amplifier that can be offset using the OFFSET
IN x pin. The DAC has a maximum output voltage span of 5 V that can be level
shifted to a maximum output voltage level of 15 V. Each output is capable of
sourcing and sinking 10 mA and driving a 10 nF load.
Analog Ground. Analog ground pins for the DAC output amplifiers on V
and V
Analog Supply. Analog supply pins for the DAC output amplifiers on V
V
Digital Output. Selectable as an alert or busy output function in the
configuration register. This is an open-drain output. An external pull-up
resistor is required.
When configured as an alert, this pin acts as an out-of-range indicator and
becomes active when the conversion result violates the DATA
register values. See the Alert Status Registers section.
When configured as a busy output, this pin becomes active when a conversion
is in progress.
Digital Logic Input. Together, the logic state of these inputs selects a unique
I
Digital Input/Output. Serial bus bidirectional data; external pull-up resistor
required.
2
OUT
C address for the AD7294. See Table 34 for details.
DD
OUT
B, and V
and DV
OUT
/REF
B, and V
IN
OUT
DD
DAC pin.
C and V
pins together to ensure that all supply pins are at the same
OUT
C and V
OUT
IN
DD
). Enable the internal reference by writing to the
D, respectively. The operating range is 4.5 V to 16.5 V.
− 2 V can be supplied to the REF
OUT
D, respectively.
OUT
/REF
IN
DAC pin is common to all
DD
pin.
OUT
Data Sheet
portion of the
HIGH
or DATA
OUT
OUT
A and
LOW
A