AD9640 Analog Devices, AD9640 Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9640
Manufacturer Part Number
AD9640
Description
14-Bit, 80/105/125/150 MSPS, 1.8 V Dual Analog-to-Digital Converter
Manufacturer
Analog Devices
Datasheet
1.AD9640.pdf
(52 pages)
Specifications of AD9640
Resolution (bits)
14bit
# Chan
2
Sample Rate
150MSPS
Interface
Par
Analog Input Type
Diff-Uni
Ain Range
1 V p-p,2 V p-p
Adc Architecture
Pipelined
Pkg Type
CSP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9640ABCPZ-105
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9640ABCPZ-125
Manufacturer:
ADI
Quantity:
158
Part Number:
AD9640ABCPZ-125
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9640ABCPZ-80
Manufacturer:
ADI
Quantity:
158
Part Number:
AD9640ABCPZ-80
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9640ABCPZRL7-80
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9640BCPZ-105
Manufacturer:
AD
Quantity:
853
Company:
Part Number:
AD9640BCPZ-125
Manufacturer:
ADI
Quantity:
161
Part Number:
AD9640BCPZ-125
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9640
Figure 69 illustrates the rms magnitude monitoring logic.
For rms magnitude mode, the value in the signal monitor result
(SMR) register is a 20-bit fixed-point number. The following
equation can be used to determine the rms magnitude in dBFS
from the MAG value in the register. Note that if the signal monitor
period (SMP) is a power of 2, the second term in the equation
becomes 0.
For ms magnitude mode, the value in the SMR is a 20-bit fixed-
point number. The following equation can be used to determine
the ms magnitude in dBFS from the MAG value in the register.
Note that if the SMP is a power of 2, the second term in the
equation becomes 0.
THRESHOLD CROSSING MODE
In the threshold crossing mode of operation, the magnitude of
the input port signal is monitored over a programmable time
period (given by the SMPR) to count the number of times it
crosses a certain programmable threshold value. This mode is set
by programming Logic 1x (where x is a don’t care bit) in the
signal monitor mode bits of the signal monitor control register
or by setting the threshold crossing output enable bit in the
signal monitor SPORT control register. Before activating this
mode, the user needs to program the 24-bit SMPR and the
13-bit upper threshold register for each individual input port.
The same upper threshold register is used for both signal moni-
toring and gain control (see the ADC Overrange and Gain
Control section).
After entering this mode, the value in the SMPR is loaded into
a monitor period timer, and the countdown is started. The magni-
tude of the input signal is compared with the upper threshold
register (programmed previously) on each input clock cycle.
If the input signal has a magnitude greater than the upper
threshold register, the internal count register is incremented by 1.
The initial value of the internal count register is set to 0. This
comparison and incrementing of the internal count register
continues until the monitor period timer reaches a count of 1.
MEMORY
PORTS
FROM
FROM
INPUT
MAP
RMS Magnitude = 20 log
MS Magnitude = 10 log
Figure 69. ADC Input RMS Magnitude Monitoring Block Diagram
PERIOD REGISTER
SIGNAL MONITOR
ACCUMULATOR
CLEAR
LOAD
COUNTER
⎛
⎜
⎝
DOWN
⎛
⎜
⎝
MAG
2
MAG
20
2
20
⎞
⎟
⎠
SIGNAL MONITOR
REGISTER (SMR)
−
⎞
⎟
⎠
LOAD
−
IS COUNT = 1?
10
HOLDING
10
log
log
⎡
⎢ ⎣
2
⎡
⎢ ⎣
ceil
2
ceil
SMP
[
log
[
SMP
MAP/SPORT
log
2
MEMORY
(
SMP
2
(
TO
SMP
)
]
)
⎤
⎥ ⎦
]
Rev. B | Page 36 of 52
⎤
⎥ ⎦
MEMORY
MEMORY
When the monitor period timer reaches a count of 1, the value
in the internal count register is transferred to the signal monitor
holding register, which can be read through the SPI port or output
through the SPORT serial port.
The monitor period timer is reloaded with the value in the SMPR
register, and the countdown is restarted. The internal count
register is also cleared to a value of 0. Figure 70 illustrates the
threshold crossing logic. The value in the SMR register is the
number of samples that have a magnitude greater than the
threshold register.
ADDITIONAL CONTROL BITS
For additional flexibility in the signal monitoring process, two
control bits are provided in the signal monitor control register.
They are the signal monitor enable bit and the complex power
calculation mode enable bit.
Signal Monitor Enable Bit
The signal monitor enable bit, Bit 0 of Register 0x112, enables
operation of the signal monitor block. If the signal monitor
function is not needed in a particular application, this bit should
be cleared (default) to conserve power.
Complex Power Calculation Mode Enable Bit
When this bit is set, the part assumes that Channel A is digitizing
the I data and Channel B is digitizing the Q data for a complex
input signal (or vice versa). In this mode, the power reported is
equal to the following:
This result is presented in the Signal Monitor DC Value Channel A
register if the signal monitor mode bits are set to 00. The Signal
Monitor DC Value Channel B register continues to compute the
Channel B value.
DC CORRECTION
Because the dc offset of the ADC may be significantly larger
than the signal being measured, a dc correction circuit is included
to null the dc offset before measuring the power. The dc correction
circuit can also be switched into the main signal path, but this
may not be appropriate if the ADC is digitizing a time-varying
signal with significant dc content, such as GSM.
PORTS
FROM
FROM
INPUT
FROM
MAP
MAP
THRESHOLD
I +
PERIOD REGISTER
SIGNAL MONITOR
REGISTER
2
Figure 70. ADC Input Threshold Crossing Block Diagram
UPPER
Q
A
2
COMPARE
A>B
B
LOAD
COUNTER
CLEAR
DOWN
COMPARE
A>B
IS COUNT = 1?
SIGNAL MONITOR
REGISTER (SMR)
LOAD
HOLDING
MAP/SPORT
MEMORY
TO